oldhui
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

oldhui 24/02/2020
I am the one who asked if the SSID and WiFi password can be changed on this product. I can confirm that it is possible to change. (Otherwise this product is useless if the password is fixed as everyone can connect to your drone.) To connect to Pixhawk, you need to set your telemetry port to a baud rate of 912600. I cannot initiate the terminal/CLI in Mission Planner. However, if you go to the full parameter list/tree, you can find it under SERIAL. Depending on you are using telemetry port 1 or 2, you can set the port to use MAVLINK with the correct baud rate. The module comes with a default SSID and wifi password. Once you are connected to the access point, use a browser to browse the URL 192.168.4.1. You will see a web page. From here you can change the SSID and wifi password. Be warned: The default firmware text is in simplfied Chinese. You can also flash the firmware here. It is actually using the ESP8266 Mavlink wifi bridge firmware version 1.2.2. You can get the 1.2.2 firmware bin file from Github. Once flashed, the default SSID is PixRacer, wifi password "pixracer". All functions are the same.
MAVLink Wifi Bridge 2.4G Wireless Wifi Telemetry Module with Antenna for Pixhawk APM Flight Controller
US$14.99 US$17.99
3
Recommendations
Comments (0)
oldhui 29/10/2020
Magnet strength is ok. If you use it with a stiffer cable it may disconnect. On a MacBook Pro, HDMI via this adaptor is unstable. It working for a while and then it disconnects. It could be related to stiff cable of the USB-HDMI adaptor I use as it may pull it off. It is annoying as swithing between display takes a while. I will only use this for charging. It seems fine for this purpose alone.
Magnetic USB C Adapter 20Pins Type C Connector PD 100W Quick Charge 10Gbp/s
US$23.99 US$28.99
0
Recommendations
Comments (1)
oldhui 02/09/2020
Item received very quickly. Connectors are correct and there is no need to reverse them. Need to print case and mount for the Anycubic Linear Plus but there are many models available in Thingiverse. The cable openings on the back may not fit though. I didn't check before printing and need to do some post-processing. It is better to check and edit the models before printing. Configuring Marlin 1.1.8 (waiting for SKR 1.4 Turbo for Marlin 2.0) is quite straight-forward: Just enable display as REPRAP_DISCOUNT_FULL_GAPHIC_SMART_CONTROLLER in Configuration.h. I also disabled MENU_HOLLOW_FRAME in Configuration_adv.h for inverted menu selection, which looks better than just 2 horizontal bars.
Intelligent Digital LCD 12864 Display 3D Printer Controller For RAMPS 1.4 Reprap
US$19.99 US$23.99
0
Recommendations
Comments (0)
MAVLink Wifi Bridge 2.4G Wireless Wifi Telemetry Module with Antenna for Pixhawk APM Flight Controller
US$14.99 US$17.99

Q: Can the SSID and password be changed? Otherwise everyone can connect and take over control of your drone.

Asked by oldhui on 2020-01-22 07:44:00

Invi no

2020-02-12 01:47:03 Helpful (0)
Submit
Answers (1)
oldhui 07/01/2019
These rings are very useful if you need to convert between dfferent filter sizes. In my case I use it to connect my lenses to a reverse mount adaptor. If the sizes are too far apart you may not want to stack too many adapters together. I tried all rings and the threads are all good.
9X Step Up 37-82mm + 9X Step Down 82-37mm Rings Filter Stepping Adapter
US$14.99 US$17.99
0
Recommendations
Comments (0)
oldhui 03/01/2019
This works with the Broadlink RM Pro control unit. *** Note that I do not use it with Broadlink's Android/iOS app. *** Instead, I use RM Bridge, IFTTT and link it with Google Home. Technically speaking you should be able to use Broadlink's app to learn its RF code but I haven't tried. And Broadlink's integration with Google Home is hopeless. So far it works better than Broadlink's own TC2 light switch which is super unreliable. The only downside of this unit is that the plastic seems to be not of the same quality as Broadlink's. Otherwise it is much more reliable (so far). BTW, the light shows 2 colours, which is quite good. In the off state, the light is blue. In the on state, the light turns red.
SESOO SY6-01-X EU/UK Standard Smart Touch Switch RF433 Remote Control Wall Switch 1 Gang 1 Way Wireless Light Switches For Smart Home Support Broadlink RM Pro
US$16.99 US$22.99
0
Recommendations
Comments (0)
oldhui 07/07/2018
I used this to upgrade my Anycubic Linear Plus to auto-leveling. It is more handy than manually doing the job. Manual leveling is tedious and time-consuming but I can get an almost perfect first layer. Using this kit alone (+ the newest firmware) doesn't get as good a result. At the end of the auto-leveling process I still need to manually adjust the 3 endstop screws to get a sticking first layer. However, the process is much faster than manual leveling. One star off for Anycubic giving too sort a lead. It may be long enough for the non-Plus. For the Plus model I need to make an extension. Giving that it is basically a microswitch with a lead, you can most likely DIY or 3D-print it. However, the whole package is quite neat with the magnetic attachment. BTW, the newest Cura (3.4?) just cannot upload the firmware but hangs. I tried this many times on 2 PCs and they all hung. I need to use the old Cura (15.04.6) to upload it. This is what Anycubic shows in their Youtube video.
Anycubic® 6-38V Auto Leveling Sensor Heated Bed Position Sensor For Kossel Series 3D Printer
US$18.99 US$24.99
0
Recommendations
Comments (0)
Eachine Beecore F3_EVO_Brushed Flight Control Board For Inductrix Tiny Whoop Eachine E010 E010S
US$28.99 US$34.99

Q: Where is the 5V connection for the camera? I cannot find it from the photos.

Asked by oldhui on 2017-11-13 06:08:14

Elaine Dear customer, maybe you can see this video, hope it can help you. https://youtu.be/E_hp9-patkQ

2017-11-28 03:45:56 Helpful (0)
Submit
Answers (1)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe