Долго мучился с контроллером. Датчик тока пока что не победил - показывает ересь. Когда прошивал osd, выявил перепутанные контакты на FTDI входе (RX с TX). Прошивку нужно ставить не REVO как пишут некоторые, а BLUEJAY4. OSD настраивать программой MWOSD. Обратите внимание на USB выход, если XT60 будет находится сбоку, то USB будет или впереди или сзади, это не удобно при расположении в коптере... я брал на крыло, поэтому пофиг. Ну не то что бы я рекомендовал эту плату, в принципе неплохо, но не забудьте сразу бубен купить.

Долго мучился с контроллером. Датчик тока пока что не победил - показывает ересь. Когда прошивал osd, выявил перепутанные контакты на FTDI входе (RX с TX). Прошивку нужно ставить не REVO как пишут некоторые, а BLUEJAY4. OSD настраивать программой MWOSD. Обратите внимание на USB выход, если XT60 будет находится сбоку, то USB будет или впереди или сзади, это не удобно при расположении в коптере... я брал на крыло, поэтому пофиг. Ну не то что бы я рекомендовал эту плату, в принципе неплохо, но не забудьте сразу бубен купить.

Долго мучился с контроллером. Датчик тока пока что не победил - показывает ересь. Когда прошивал osd, выявил перепутанные контакты на FTDI входе (RX с TX). Прошивку нужно ставить не REVO как пишут некоторые, а BLUEJAY4. OSD настраивать программой MWOSD. Обратите внимание на USB выход, если XT60 будет находится сбоку, то USB будет или впереди или сзади, это не удобно при расположении в коптере... я брал на крыло, поэтому пофиг. Ну не то что бы я рекомендовал эту плату, в принципе неплохо, но не забудьте сразу бубен купить.

The target file is BlueJayF4. In BF 3.1 the LED pad will not work because of the resource shifting for dshot. In BF 3.0 it works normal. You can switch back the rescources to activate the LED pad in BF 3.1 in CLI but it won't work together with dshot. If you don't need LED Strip (I do) - Dshot will work out of the box.

The target file is BlueJayF4. In BF 3.1 the LED pad will not work because of the resource shifting for dshot. In BF 3.0 it works normal. You can switch back the rescources to activate the LED pad in BF 3.1 in CLI but it won't work together with dshot. If you don't need LED Strip (I do) - Dshot will work out of the box.

The target file is BlueJayF4. In BF 3.1 the LED pad will not work because of the resource shifting for dshot. In BF 3.0 it works normal. You can switch back the rescources to activate the LED pad in BF 3.1 in CLI but it won't work together with dshot. If you don't need LED Strip (I do) - Dshot will work out of the box.

Bad esc layout. The signal wires are not allocated properly for a side mount board. USB port in wrong location. Very small auxiliary and receiver pads. Mine has a faulty gyro so it's unflyable. Inconsistent yaw gyro sensor. Avoid!

Bad esc layout. The signal wires are not allocated properly for a side mount board. USB port in wrong location. Very small auxiliary and receiver pads. Mine has a faulty gyro so it's unflyable. Inconsistent yaw gyro sensor. Avoid!

Bad esc layout. The signal wires are not allocated properly for a side mount board. USB port in wrong location. Very small auxiliary and receiver pads. Mine has a faulty gyro so it's unflyable. Inconsistent yaw gyro sensor. Avoid!

I like the video switching capabilities of this board. Great execution on that. The F3 controller and solder points are fine - small, but ok. The issue that I have with this is it seems to have a sensitive gyro on it AND the gyro doesn't allow 32khz, which makes less sense to me. Was only able to get 4khz/4khz, but DSHOT seems to work without issue. Otherwise, very happy with this board and with the video performance.

I like the video switching capabilities of this board. Great execution on that. The F3 controller and solder points are fine - small, but ok. The issue that I have with this is it seems to have a sensitive gyro on it AND the gyro doesn't allow 32khz, which makes less sense to me. Was only able to get 4khz/4khz, but DSHOT seems to work without issue. Otherwise, very happy with this board and with the video performance.

I like the video switching capabilities of this board. Great execution on that. The F3 controller and solder points are fine - small, but ok. The issue that I have with this is it seems to have a sensitive gyro on it AND the gyro doesn't allow 32khz, which makes less sense to me. Was only able to get 4khz/4khz, but DSHOT seems to work without issue. Otherwise, very happy with this board and with the video performance.

Issue on one of the units USB came right off (lose connector) and on the other unit sbus would not work no matter what i tried. Eventually it would not even recognize it.

Issue on one of the units USB came right off (lose connector) and on the other unit sbus would not work no matter what i tried. Eventually it would not even recognize it.

Issue on one of the units USB came right off (lose connector) and on the other unit sbus would not work no matter what i tried. Eventually it would not even recognize it.

Perfect

Perfect

Perfect

ottimo prodotto svolge al meglio le sue funzioni lo consiglio a tutti

ottimo prodotto svolge al meglio le sue funzioni lo consiglio a tutti

ottimo prodotto svolge al meglio le sue funzioni lo consiglio a tutti

conforme a la description

conforme a la description

conforme a la description

Very good quality

Very good quality

Very good quality

This work nice

This work nice

This work nice