EXC000
mitt innehåll
Alla meddelanden
recensioner
kommentarer
svar
frågor

Alla meddelanden

EXC000 11/04/2019
Works well on Ender 3, BUT if your control board has capacitor C7 installed (see photo) then you must remove it, or the very short duration Z-stop signal from BLTouch will not be detected and the extruder will just crash into the print bed when it auto-homes. This is a known issue with BLTouch and the latest Ender 3 control boards leave out C7. To refit the Ender 3/Pro cover and fan, you need to bend the four pins on the adapter PCB so that the 4-way header from BLTouch is horizontal. Versions of this kit sold elsewhere have the pins already bent.
Creality 3D® Uppgraderad Version BL-Touch Uppvärmd Säng Automatisk Nivågivare Kit För Creality V1 Huvudkort Inklusive Ender-3/Ender-3s/Ender-3 Pro 3D-Skrivare
US$41.00 US$53.99
13
rekommendationer
kommentarer (0)
EXC000 12/03/2019
Works OK with factory-assigned code and a learning receiver. No instructions supplied on changing it. Access to change battery is difficult because the case has no coin/fingernail slot to lever apart the two pieces.
433Mhz Trådlös Fjärrkontroll Växelspak 6V 4 Kanaler
US$3.66 US$6.66
1
rekommendationer
kommentarer (0)
EXC000 12/03/2019
Works well, using the remote from https://www.banggood.com/433Mhz-Transmitter-Wireless-Remote-Control-Switch-12V-4CH-Channel-p-1018573.html we get about 50m outdoor range. Note the status LED is on all the time (flashes off when data is received), so there is a bit of wasted current draw, could be important for battery powered receivers.
433,92 MHz Superheterodyne Lärande Mottagarmodul Trådlöst Mottagningskort med Avkodningsmottagare
US$8.99 US$10.99
1
rekommendationer
kommentarer (1)
Creality 3D® Uppgraderad Version BL-Touch Uppvärmd Säng Automatisk Nivågivare Kit För Creality V1 Huvudkort Inklusive Ender-3/Ender-3s/Ender-3 Pro 3D-Skrivare
US$41.00 US$53.99

Q: Hi, it works with Ender 3 Mainboard Creality 3D V1.1.3? Thanks.

frågade av osvaldo på 2019-03-17 06:03:12

EXC000 You need to de-solder capacitor C7 from the 1.1.3 mainboard (next to the Z-STOP connector) otherwise the trigger signal will not be detected. BLTouch sends a very short pulse when it contacts the print bed, and the capacitor suppresses it. On later mainboards C7 is not fitted because of this problem.

2019-04-12 09:45:49 Hjälpsam (1)
Lämna
svar (4)

Du är experten, kan du hjälpa till?

Vi inbjuder dig att prenumerera på e-postmeddelandet Bjud in svar!

Om du prenumererar bjuder vi in dig via e-post för att svara på frågor som människor har om produkter. Genom att prenumerera på dig] tjänar du också "Helpful Badge "! Du kan när som helst avsluta prenumerationen på sekretessinställningssidan.

Hjälp andra och bli lyckligare!

  • Prenumerera

Om märken

Märken är relaterade till samhället, och användare tjänar märken genom att skapa kvalitetsinnehåll, genomföra uppdrag eller genom att delta i speciella aktiviteter. Specifika personer kommer också att ha sitt eget exklusiva märke.
VD Badge

VD-märket ägs endast av chefen för Banggood.

Märken du kan tjäna kommer snart
  • ok

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • ok

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe