Not so happy with this as the plug at the front was only holding on with 1 pin and so it won't work. quality control not the best with the drak esc

Not so happy with this as the plug at the front was only holding on with 1 pin and so it won't work. quality control not the best with the drak esc

Not so happy with this as the plug at the front was only holding on with 1 pin and so it won't work. quality control not the best with the drak esc

справляется на ура с 2035 трехлопастными пропами на 1105 8500кв 3s.

справляется на ура с 2035 трехлопастными пропами на 1105 8500кв 3s.

справляется на ура с 2035 трехлопастными пропами на 1105 8500кв 3s.

Do Not drill to 3mm! :D I did, had to remap the positive!

Do Not drill to 3mm! :D I did, had to remap the positive!

Do Not drill to 3mm! :D I did, had to remap the positive!

1. Tiny resistor between GND pad and MOSFET. Shortcut risik. 2. Also tiny resistors between motor pads and MOSFETS. Not so bad but need to be carefull too. 3. Worst part - some elements getting in to screw area and nut's can damage them. I wish to see this model v2 with M3 holes and with better space around screws. Nothing else is need.

1. Tiny resistor between GND pad and MOSFET. Shortcut risik. 2. Also tiny resistors between motor pads and MOSFETS. Not so bad but need to be carefull too. 3. Worst part - some elements getting in to screw area and nut's can damage them. I wish to see this model v2 with M3 holes and with better space around screws. Nothing else is need.

1. Tiny resistor between GND pad and MOSFET. Shortcut risik. 2. Also tiny resistors between motor pads and MOSFETS. Not so bad but need to be carefull too. 3. Worst part - some elements getting in to screw area and nut's can damage them. I wish to see this model v2 with M3 holes and with better space around screws. Nothing else is need.

original esc on Arfun 90 and 95

original esc on Arfun 90 and 95

original esc on Arfun 90 and 95

Its difficult to mount this without causing damage. The distance between the mount hole and the components means you can't turn a nut or hex standoff without it pushing against the component. That's OK if you can easily access the bolt head, but not ideal if you want to use hex standoffs above and below. Otherwise fine, no real issues

Its difficult to mount this without causing damage. The distance between the mount hole and the components means you can't turn a nut or hex standoff without it pushing against the component. That's OK if you can easily access the bolt head, but not ideal if you want to use hex standoffs above and below. Otherwise fine, no real issues

Its difficult to mount this without causing damage. The distance between the mount hole and the components means you can't turn a nut or hex standoff without it pushing against the component. That's OK if you can easily access the bolt head, but not ideal if you want to use hex standoffs above and below. Otherwise fine, no real issues

Works fine. The board is a little crowded around the mounting holes, not easy to screw in a standoff. You have to hold the standoff on top and screw in a screw from the underside.

Works fine. The board is a little crowded around the mounting holes, not easy to screw in a standoff. You have to hold the standoff on top and screw in a screw from the underside.

Works fine. The board is a little crowded around the mounting holes, not easy to screw in a standoff. You have to hold the standoff on top and screw in a screw from the underside.

Lots of amps in such small pack

Lots of amps in such small pack

Lots of amps in such small pack

Nice upgrade for the eachine minitower stack. Same size but almost twice the current capacity as the stock unit. I have this running 3s in a 150 quad, 3 inch triblade props running Dshot 600, with no signs of excess heat. Nice solution.

Nice upgrade for the eachine minitower stack. Same size but almost twice the current capacity as the stock unit. I have this running 3s in a 150 quad, 3 inch triblade props running Dshot 600, with no signs of excess heat. Nice solution.

Nice upgrade for the eachine minitower stack. Same size but almost twice the current capacity as the stock unit. I have this running 3s in a 150 quad, 3 inch triblade props running Dshot 600, with no signs of excess heat. Nice solution.

great for micro quad

great for micro quad

great for micro quad