Utilizado como interruptor de aquecimento por indução 2,5 kW

Použito jako spínač indukčního ohřevu 2,5kW

Utilizado como interruptor de aquecimento por indução 2,5 kW

Hallo getestet am Heizbett eines Prusa i3 (anet a8) Pin1 an - Pin2 auf das Heizbett von da an + (das Relais schaltet nach -) 16V / 12A (mehr bringt mein Labornetzteil nicht) und angesteuert mit 12V (5 reichen aber auch) das SSR wird kaum fühlbar warm - quasi nix Spannungsabfall ca. 100mV am Relais = 0.0083 Ohm - sehr gut (mein selbstgebauter SevenSwitch hat 0.003 aber kein so schönes Gehäuse) (bei amazon D gibts nur billige Clone die nichts taugen) Das hier ist einwandfrei ! ------------------------------ Hello this SSR works very good testet with Heatbed - 16V/12A Voltage drop on SSR = 0.1 V 0.1V on 12A = 0.0083 Ohm - very good it is switching the - so Heatbed goes on Pin 2

Hallo getestet am Heizbett eines Prusa i3 (anet a8) Pin1 an - Pin2 auf das Heizbett von da an + (das Relais schaltet nach -) 16V / 12A (mehr bringt mein Labornetzteil nicht) und angesteuert mit 12V (5 reichen aber auch) das SSR wird kaum fühlbar warm - quasi nix Spannungsabfall ca. 100mV am Relais = 0.0083 Ohm - sehr gut (mein selbstgebauter SevenSwitch hat 0.003 aber kein so schönes Gehäuse) (bei amazon D gibts nur billige Clone die nichts taugen) Das hier ist einwandfrei ! ------------------------------ Hello this SSR works very good testet with Heatbed - 16V/12A Voltage drop on SSR = 0.1 V 0.1V on 12A = 0.0083 Ohm - very good it is switching the - so Heatbed goes on Pin 2

Hallo getestet am Heizbett eines Prusa i3 (anet a8) Pin1 an - Pin2 auf das Heizbett von da an + (das Relais schaltet nach -) 16V / 12A (mehr bringt mein Labornetzteil nicht) und angesteuert mit 12V (5 reichen aber auch) das SSR wird kaum fühlbar warm - quasi nix Spannungsabfall ca. 100mV am Relais = 0.0083 Ohm - sehr gut (mein selbstgebauter SevenSwitch hat 0.003 aber kein so schönes Gehäuse) (bei amazon D gibts nur billige Clone die nichts taugen) Das hier ist einwandfrei ! ------------------------------ Hello this SSR works very good testet with Heatbed - 16V/12A Voltage drop on SSR = 0.1 V 0.1V on 12A = 0.0083 Ohm - very good it is switching the - so Heatbed goes on Pin 2

Very good solid state relay

Very good solid state relay

Very good solid state relay

I wouldn't put 100 amps on it, but for general use, it is totally fine! It surprised me that it actually came with a top cover to cover up the terminals.

I wouldn't put 100 amps on it, but for general use, it is totally fine! It surprised me that it actually came with a top cover to cover up the terminals.

I wouldn't put 100 amps on it, but for general use, it is totally fine! It surprised me that it actually came with a top cover to cover up the terminals.

Using this on a 3D printer to heat a bed oversized for a standard RAMPS board. Works perfectly well and allows PID control of the heated bed from Marlin firmware.

Using this on a 3D printer to heat a bed oversized for a standard RAMPS board. Works perfectly well and allows PID control of the heated bed from Marlin firmware.

Using this on a 3D printer to heat a bed oversized for a standard RAMPS board. Works perfectly well and allows PID control of the heated bed from Marlin firmware.

... as it should. Tested up to 30A.

... as it should. Tested up to 30A.

... as it should. Tested up to 30A.

Arrived quickly, as depicted, new condition. This is the first time I purchased a solid state relay. It is amazing ! Totally silent, instant, and has an LED indicator. Thank you banggood.com

Arrived quickly, as depicted, new condition. This is the first time I purchased a solid state relay. It is amazing ! Totally silent, instant, and has an LED indicator. Thank you banggood.com

Arrived quickly, as depicted, new condition. This is the first time I purchased a solid state relay. It is amazing ! Totally silent, instant, and has an LED indicator. Thank you banggood.com

Está bem, está bem

ok

Está bem, está bem

O produto parece bom. Entrega rápida para

Product looks good. quick delivery to

O produto parece bom. Entrega rápida para

doubts about 100A ... ... . . ... ... .... ....

doubts about 100A ... ... . . ... ... .... ....

doubts about 100A ... ... . . ... ... .... ....