Szczypior
Q: black and red wires on rear camera what is it for ?
spurte av sergzadoroz på 2017-11-29 07:05:57
Szczypior It's for powering it. There is separate connection of the circuit required in order to rear camera to work.
2023-04-24 03:44:49 Hjelpsom (0)Q: does it come with the transmitter
spurte av BG403745454 på 2023-04-24 06:44:32
Szczypior This is reciever only. Transmitter has to be bought separately
2023-04-24 03:44:37 Hjelpsom (0)
Szczypior Yes, it supports all common frequencies of analog transmission
2023-04-19 02:35:55 Hjelpsom (0)
Q: hey does it come with everything needed to run controller ect
spurte av rcmad94 på 2020-10-31 02:51:16
Szczypior This is a KIT version, so basically a plastic model without any electronics. mine came with a motor, but no ESC or receiver.
2020-11-01 12:43:26 Hjelpsom (0)Q: Is this in stock? Do I need a special antenna for this?
spurte av Sarbjit Billing på 2020-06-03 06:50:49
Szczypior It comes with no antenna so you need to order them separately. It uses SMA connector. Of course it's 2,4GHz reciever.
2020-06-03 06:54:01 Hjelpsom (0)Q: can i use 3s 2200mah 11.1v lipojQuery111305403163780715163_1590404824781?
spurte av BG264711952 på 2020-05-25 06:13:51
Szczypior yes, it supports 3-6S
2020-05-25 06:21:45 Hjelpsom (1)Q: Other than the price, why would I choose this one than the new Jumber versions?
spurte av jAm på 2020-04-26 04:11:29
Szczypior The communication in group is terrible. Bad comments are deleted, so Helikido is actually not right and delusional.
2020-05-21 12:11:12 Hjelpsom (0)Q: FURYF4OSD (Legacy) or (Diatone)?
spurte av dariuszkazmierczak8 på 2020-05-16 02:04:16
Szczypior Diatone site states it's legacy.
2020-05-16 02:16:44 Hjelpsom (0)Q: Is the thread straight through?
spurte av Sarel MVenter på 2019-09-02 06:22:21
Szczypior In my case it was.
2020-04-04 02:39:00 Hjelpsom (0)Q: What kind of led does it support ? Only Mamba led or any WS2812 would works ?
spurte av gabrielforray på 2020-04-04 08:31:51
Szczypior Any kind of LEDs, but keep in mind that 5V regulator has limited amperage. If you are willing to use some high power LEDs then you just take signal pad from FC and power up LEDs from other source. Of course this FC is not dedicated to any kind of LEDs manufacturer.
2020-04-04 02:38:17 Hjelpsom (0)Q: Will the Pin of Battery Fit with Nano Fpv Camera Pin??
spurte av adityash840 på 2018-06-15 07:19:08
Szczypior Very unlikely as this is PH2.0 and cameras use smaller plugs in most cases.
2020-03-27 05:00:38 Hjelpsom (0)Vi inviterer deg hjertelig til å abonnere på e-posten Inviter svar!
Hvis du abonnerer, vil vi invitere deg via e-post for å svare på spørsmål folk har om produkter. Ved å abonnere vil du også tjene "Helpful Badge "! Du kan når som helst avslutte abonnementet på siden for personverninnstillinger.
Hjelp andre og vær lykkeligere!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Szczypior There are alternatives on the BG with similar AWG
2023-04-24 03:46:39 Hjelpsom (0)