WeirdAl
Q: power supply voltage?? dc supply voltage??
gevraagd door BG510423750 op 2021-01-31 07:42:50
WeirdAl The product says that it needs from 6-36 volts, DC... It will only give you what you give it, plus a couple volts.I have mine hooked up 2 x 12 volt batteries...
2021-02-09 01:08:17 Nuttig (0)
WeirdAl@BG232244242 Notif the Z-Axis is not accurate... This review just made me question my purchase...
Q: which is the brand producer?
gevraagd door adolfoleonardi op 2020-12-06 04:17:32
WeirdAl There is no brand name on the unit, and the packaging was not marked at all.
2020-12-09 11:53:51 Nuttig (0)
Q: It work only with android or it also can record with power usb only? I mean, power usb and record.
gevraagd door BG111154905 op 2020-05-13 07:49:27
WeirdAl There is no battery in the unit I received... It only runs when it is receiving USB power.
2020-09-22 05:52:48 Nuttig (0)Q: I did not get a manual with my camera. Do you have a link to it online?
gevraagd door WeirdAl op 2020-09-21 05:49:03
Dani não tenho certeza se na minha acompanha! Vou verificar !
2020-09-22 01:07:10 Nuttig (0)
WeirdAl The conducting pin is 13.75 mm long, bent at 90% in the middle.
2020-07-28 09:58:12 Nuttig (1)
WeirdAl From the description: Dimension: 71mm*16.89mm*19.41mm (For iPhone 6) 81.9mm*16.99mm*20.14mm (For iPhone 6P) 71.1mm*16.8mm*19.4mm (For iPhone 7 - 8) 82.4mm*17.7mm*20.7mm (For iPhone 7P - 8P) 70.0mm*17.6mm*20.6mm (For iPhone X) .. So I would have to say "IPhone"...
2020-07-19 12:00:05 Nuttig (0)
Mrmartinc 50.94*27.88*11.93MM
2020-07-15 01:47:07 Nuttig (1)
Gabbro These IS "dual-color" LEDs
2020-07-09 10:44:12 Nuttig (0)
Karavs Chip needs two voltage, one for logic supply and another for drive supply. From data sheets I found that max voltage for logic is 7 v and for drive - 50 v. This is parameters for chip. On board I see 12 v and 5 v supply inputs, where you found 5v-35v? 12 v is for drive supply (chip input 4) and 5v is for logic support (chip input 9)
2020-01-28 11:47:49 Nuttig (0)
bice90 Hi! In this case, you can do a little research, but TLDR: you can go up to 35 V, no problems, but you have to remove the jumper located above the power supply connector. Longer answer: 1st, you can see that the capacitors are rated for 35V (220 35V VT). Also, you can check the datasheet of the L298N chip which says that the maximum supply voltage is 46 V (page 3 of the datasheet). You have to be aware that there is a jumper on the board which should be removed if you use the device with larger than 12 V. The jumper is located between the input terminal and one of the capacitors (bottom left corner of the board). I also tested this type of circuit board with different voltages and it was fine. In fact, my board does not have the 12 V printed on it.
2020-02-03 12:06:59 Nuttig (2)
We nodigen je van harte uit om je te abonneren op de Invite Answer-e-mail!
Als u zich abonneert, nodigen we u uit via e-mail om vragen te beantwoorden die mensen hebben over producten. Door je te abonneren, verdien je ook de "Behulpzame Badge "! U kunt zich op elk moment uitschrijven op de pagina met privacyinstellingen.
Help anderen en wees gelukkiger!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
.jpg)
