As you may have read in other reviews, the sticks are excellent in both quality/workmanship and functionality. However, they do not fit M9 gimbals out of the box, due to lower portion being too thin. Here is how I have modded mine to fit, if you don't mind loosing some of the bottom conical part. Cut off the bottom half of conical section, leaving only 4.5-5mm (see my last pic in reference to original stick). Do not try and leave it any longer as it will tear the sides while you drill into it, and end up with it even shorter. After cutting, use a 7/32 drill bit (3/16 is too small) to drill out the conical section to allow it to fit over the stick. A tip here is to use a 4mm bolt through the rocker to allow you to hold it and also to stop the drill bit from going into the threaded portion (only screw the bolt up to the end of the thread). I've also added a bit of black heat-shrink to make up for the cut off part and think it looks really slick.

As you may have read in other reviews, the sticks are excellent in both quality/workmanship and functionality. However, they do not fit M9 gimbals out of the box, due to lower portion being too thin. Here is how I have modded mine to fit, if you don't mind loosing some of the bottom conical part. Cut off the bottom half of conical section, leaving only 4.5-5mm (see my last pic in reference to original stick). Do not try and leave it any longer as it will tear the sides while you drill into it, and end up with it even shorter. After cutting, use a 7/32 drill bit (3/16 is too small) to drill out the conical section to allow it to fit over the stick. A tip here is to use a 4mm bolt through the rocker to allow you to hold it and also to stop the drill bit from going into the threaded portion (only screw the bolt up to the end of the thread). I've also added a bit of black heat-shrink to make up for the cut off part and think it looks really slick.

As you may have read in other reviews, the sticks are excellent in both quality/workmanship and functionality. However, they do not fit M9 gimbals out of the box, due to lower portion being too thin. Here is how I have modded mine to fit, if you don't mind loosing some of the bottom conical part. Cut off the bottom half of conical section, leaving only 4.5-5mm (see my last pic in reference to original stick). Do not try and leave it any longer as it will tear the sides while you drill into it, and end up with it even shorter. After cutting, use a 7/32 drill bit (3/16 is too small) to drill out the conical section to allow it to fit over the stick. A tip here is to use a 4mm bolt through the rocker to allow you to hold it and also to stop the drill bit from going into the threaded portion (only screw the bolt up to the end of the thread). I've also added a bit of black heat-shrink to make up for the cut off part and think it looks really slick.

X9D Plus SE 2019 のスティックの先端だけを交換して使えます。標準のスティックはサムナー向けの形状でピンチャーの私には操作しにくかったので、交換したら繊細なコントロールがやりやすくなりました。（個人的な感想です。）

X9D Plus SE 2019 のスティックの先端だけを交換して使えます。標準のスティックはサムナー向けの形状でピンチャーの私には操作しにくかったので、交換したら繊細なコントロールがやりやすくなりました。（個人的な感想です。）

X9D Plus SE 2019 のスティックの先端だけを交換して使えます。標準のスティックはサムナー向けの形状でピンチャーの私には操作しにくかったので、交換したら繊細なコントロールがやりやすくなりました。（個人的な感想です。）

The lower part does not fit frsky M9 gimbal.

The lower part does not fit frsky M9 gimbal.

The lower part does not fit frsky M9 gimbal.

good for Radiomaster TX16S but you need to cut from them because are to long

good for Radiomaster TX16S but you need to cut from them because are to long

good for Radiomaster TX16S but you need to cut from them because are to long

Хорошие стики и по очень за не дорого. Установил с одним не большим но! Нижняя часть стика юбочка не подошла на мой передатчик. Оставил свою юбочку. Вобщем за такую цену думаю что лучше не найти.

Хорошие стики и по очень за не дорого. Установил с одним не большим но! Нижняя часть стика юбочка не подошла на мой передатчик. Оставил свою юбочку. Вобщем за такую цену думаю что лучше не найти.

Хорошие стики и по очень за не дорого. Установил с одним не большим но! Нижняя часть стика юбочка не подошла на мой передатчик. Оставил свою юбочку. Вобщем за такую цену думаю что лучше не найти.

Kleiner "Farbtupfer" für meine Radiomaster TX16S

Kleiner "Farbtupfer" für meine Radiomaster TX16S

Kleiner "Farbtupfer" für meine Radiomaster TX16S

perfetti e molto comodi un po' più lunghi degli originali

perfetti e molto comodi un po' più lunghi degli originali

perfetti e molto comodi un po' più lunghi degli originali

I knew these are not for Taranis but I still wanted to try out since the screw size is the same 4mm. Mounted on Taranis X9D Plus SE 2019, with partial results, still usable. The issue is that the lower part of these is not wider as the Taranis original sticks ,but can be combined as in the attached images.

I knew these are not for Taranis but I still wanted to try out since the screw size is the same 4mm. Mounted on Taranis X9D Plus SE 2019, with partial results, still usable. The issue is that the lower part of these is not wider as the Taranis original sticks ,but can be combined as in the attached images.

I knew these are not for Taranis but I still wanted to try out since the screw size is the same 4mm. Mounted on Taranis X9D Plus SE 2019, with partial results, still usable. The issue is that the lower part of these is not wider as the Taranis original sticks ,but can be combined as in the attached images.

these are the colors I wanted I ordered a transmitter that came with pink and it didn’t look right so I wanted red and it’s perfect

these are the colors I wanted I ordered a transmitter that came with pink and it didn’t look right so I wanted red and it’s perfect

these are the colors I wanted I ordered a transmitter that came with pink and it didn’t look right so I wanted red and it’s perfect

theese sticks looks very Nicei fitted on my flysky fs i6 with some mods .

theese sticks looks very Nicei fitted on my flysky fs i6 with some mods .

theese sticks looks very Nicei fitted on my flysky fs i6 with some mods .