すべてのメッセージ

Q: Does it do full acro? Can you use tri blade props? thanks

尋ねた BG121712837 に 2021-10-03 04:27:51

DonKracho Yes it can do acro mode depending on you betaflight settings. It is nuch much more agile compared to a Tini Hawk with 1S

2022-05-01 07:57:48 役に立つ (0)
提出
回答 (5)

DonKracho The UZ80 can fly very stable and slow depending on yout transmitter and betaflight settings. But I do not recommend to use it in free nature! The UZ 80 has no alarm beeper. If you crash you may not find it even in high gras.

2022-05-01 07:53:11 役に立つ (1)
提出
回答 (7)

Q: Is 3.7 lipo or 3.8 LiHV?

尋ねた maxycma に 2022-04-30 10:33:40

DonKracho The specifications of contoller and ESC to allow 1S LiHV (4.35V). I use it with LiHV too. The voltage is slightly higer only and does not break the electronics.

2022-05-01 07:44:05 役に立つ (0)
提出
回答 (1)

Q: Please explain Tilt vertical: 120°. What is maximum up/down?

尋ねた BG175411619 に 2020-09-15 10:16:40

DonKracho Unfortunately it can not look up. From horizontal it goes to straight down 90° and further 30° up again. In summary 120°

2021-06-09 05:39:19 役に立つ (0)
提出
回答 (1)

Q: what is the rtsp url syntax to stream image on VLC?

尋ねた BG131881332 に 2020-12-26 07:02:57

DonKracho By default use rtsp: slash slash [ip of your cam]:554 slash 11 for mainstream or 12 for substream. rtsp can be configured to require credentials.

2021-06-09 05:32:47 役に立つ (1)
提出
回答 (2)

Q: what is the recording format, h264 or h265?

尋ねた BG316133819 に 2021-03-16 04:22:52

DonKracho It can be configured for booth H.264 (baseline, mainprofile, highprofile) or H.265 (mainprofile)

2021-06-09 05:15:19 役に立つ (1)
提出
回答 (3)

Q: Can the camera firmware be updated if necessary?

尋ねた tholl に 2020-10-28 03:29:04

DonKracho As long as there are no faults, I would not recommend to update the firmware. There is firmware on www.ipcam.xin and can be updatated via the webserver integrated in the cam (http: ip of your cam). The firmware update applies a factory reset. Be aware that you will loose the WiFi connection.

2021-06-09 05:00:12 役に立つ (2)
提出
回答 (5)

Q: this controlled with the eWelink app ?

尋ねた JinXed に 2021-01-10 08:41:15

DonKracho No, The sample sketch preinstalled just switches the Relays in a sequence. The easiest way will be to flash tasmota.

2021-02-05 02:54:12 役に立つ (0)
提出
回答 (2)
DonKracho 31/03/2020
0
推奨事項
コメント (0)

DonKracho Watchout for the CAM connection. It provides 10V. The Caddx EOS will shut down at 10V (gray image). Remove the red wire from the connector and put it on a 5V rail and everythng is fine. looks like Eachine has not tested this before delivery:(

jcreyes78 26/03/2019
6
コメント (2)