Received this wing today and build completed in about 3 hours (I know it’s too long for a PNF plane). Good things- 1) Components used are of good quality. Motor is quite powerful Servos are MG and very smooth. ESC is probably HobbyWing 30A. Servo linkages are also precise. Some build issues to take note of - 1) Manual fully in Chinese can’t understand where is the CG also. 2) The CF rod installation design is the worst I have seen so far. The bar doesn’t provide enough support. not sure how many crashes it can survive. 3) FPV Camera position doesn’t seem so good. it would probably obstruct the camera. however I haven’t tried it yet but not a big problem. can cut the foam if required. 4) Canopy looks very loosely attached due to weak magnets. will have to secure using Rubber band or a tape before flight. else change the magnets to a powerful ones. 5) Propellers are of cheap quality. Buy a good quality 6x4 props. 6) Servos were installed like a big joke. They were simply fixed to the plane using a thin double sided tape which came off in just one tug. Must takeout that tape and use Uhu Por or similar glue to fix the servos. Overall the wing profile looks exactly like Z84 but just bigger than it. So I assume it should give good flight time. Will fly the plane and test it in a day or two.

Received this wing today and build completed in about 3 hours (I know it’s too long for a PNF plane). Good things- 1) Components used are of good quality. Motor is quite powerful Servos are MG and very smooth. ESC is probably HobbyWing 30A. Servo linkages are also precise. Some build issues to take note of - 1) Manual fully in Chinese can’t understand where is the CG also. 2) The CF rod installation design is the worst I have seen so far. The bar doesn’t provide enough support. not sure how many crashes it can survive. 3) FPV Camera position doesn’t seem so good. it would probably obstruct the camera. however I haven’t tried it yet but not a big problem. can cut the foam if required. 4) Canopy looks very loosely attached due to weak magnets. will have to secure using Rubber band or a tape before flight. else change the magnets to a powerful ones. 5) Propellers are of cheap quality. Buy a good quality 6x4 props. 6) Servos were installed like a big joke. They were simply fixed to the plane using a thin double sided tape which came off in just one tug. Must takeout that tape and use Uhu Por or similar glue to fix the servos. Overall the wing profile looks exactly like Z84 but just bigger than it. So I assume it should give good flight time. Will fly the plane and test it in a day or two.

Received this wing today and build completed in about 3 hours (I know it’s too long for a PNF plane). Good things- 1) Components used are of good quality. Motor is quite powerful Servos are MG and very smooth. ESC is probably HobbyWing 30A. Servo linkages are also precise. Some build issues to take note of - 1) Manual fully in Chinese can’t understand where is the CG also. 2) The CF rod installation design is the worst I have seen so far. The bar doesn’t provide enough support. not sure how many crashes it can survive. 3) FPV Camera position doesn’t seem so good. it would probably obstruct the camera. however I haven’t tried it yet but not a big problem. can cut the foam if required. 4) Canopy looks very loosely attached due to weak magnets. will have to secure using Rubber band or a tape before flight. else change the magnets to a powerful ones. 5) Propellers are of cheap quality. Buy a good quality 6x4 props. 6) Servos were installed like a big joke. They were simply fixed to the plane using a thin double sided tape which came off in just one tug. Must takeout that tape and use Uhu Por or similar glue to fix the servos. Overall the wing profile looks exactly like Z84 but just bigger than it. So I assume it should give good flight time. Will fly the plane and test it in a day or two.

excelente produto comprei duas veio numa caixa e não foi taxado muito bom

excelente produto comprei duas veio numa caixa e não foi taxado muito bom

excelente produto comprei duas veio numa caixa e não foi taxado muito bom

これは非常にタフな翼で、私は何度もそれをクラッシュし、熱い接着剤の迅速な球体と、それは空気に戻る準備ができています。 フルスロットルで、pnpモーターとプロップが叫ぶか、1.2mの翼の上で滑ることができます。 短所: 1. 用意されたプッシュロッドは短すぎるので、交換しなければなりませんでした。 2. プリインストールされたサーボは安全ではありませんので、接着する必要があります。 3. ベイへのサーボケーブルのパススルーはありません。 だから、翼を胴体に接着する前に、アクセス ポイントを計画してください。 4. ハッチキャノピーは後方に押さえて設計されており、前方に装備された磁石は、飛行中にそれを保持するには弱すぎます。 スプリングラッチが役に立つかもしれません。 今はテープを使うだけ。 このデルタウィングを出荷開始前に購入したので、大きな価値でした。 私が短所として議論したいくつかの項目は、軽微で、修理するのに安いです。 これは私の最初のデルタ翼だったので、NX3スタビライザーを追加しましたが、数回の打ち上げの後、私はちょうど約50%のスロットルと、彼女の空気に戻すためにしっかりとした翼が必要です。 だから、風が吹いているときにNX3を使うだけです。 あなたの指を保つために、打ち上げのために翼に内蔵されたハンドグリップを使用しないでください。 なぜこの翼が彼らと一緒にデザインされたのかは、心を揺さぶる。

This is a very tough wing and I have crashed it multiple times and a quick glob of hot glue and it is ready to go back into the air. Give it full throttle and the pnp motor and prop will have her screaming or it can glide on those 1.2m wings. Cons: 1. Push rods provided are too short, so I had to replace them. 2. the pre-installed Servos are not secure, so you will need to glue them. 3. There is no passthrough for servo cables to the bay. So plan you access point before you glue the wings to the fuselage. 4. Hatch canopy is designed with hold down in the rear and the provided magnets up front are too weak to hold it in place during flight. A spring latch could help. I just use tape for now. As I purchased this Delta wing before the shipping issues started, it was a great value. The few items I discussed as cons are minor and cheap to fix. This was my first Delta wing, so I added a NX3 stabilizer, but after a couple of launches I find that it just needs about 50 percent throttle and a firm wing fling to get her back into the air. So I just use the NX3 when the wind is gusting and not steady. DON'T USE the hand grips built into the wing for the launches if you want to keep your fingers. Why this wing has been designed with them boggles the mind.

これは非常にタフな翼で、私は何度もそれをクラッシュし、熱い接着剤の迅速な球体と、それは空気に戻る準備ができています。 フルスロットルで、pnpモーターとプロップが叫ぶか、1.2mの翼の上で滑ることができます。 短所: 1. 用意されたプッシュロッドは短すぎるので、交換しなければなりませんでした。 2. プリインストールされたサーボは安全ではありませんので、接着する必要があります。 3. ベイへのサーボケーブルのパススルーはありません。 だから、翼を胴体に接着する前に、アクセス ポイントを計画してください。 4. ハッチキャノピーは後方に押さえて設計されており、前方に装備された磁石は、飛行中にそれを保持するには弱すぎます。 スプリングラッチが役に立つかもしれません。 今はテープを使うだけ。 このデルタウィングを出荷開始前に購入したので、大きな価値でした。 私が短所として議論したいくつかの項目は、軽微で、修理するのに安いです。 これは私の最初のデルタ翼だったので、NX3スタビライザーを追加しましたが、数回の打ち上げの後、私はちょうど約50%のスロットルと、彼女の空気に戻すためにしっかりとした翼が必要です。 だから、風が吹いているときにNX3を使うだけです。 あなたの指を保つために、打ち上げのために翼に内蔵されたハンドグリップを使用しないでください。 なぜこの翼が彼らと一緒にデザインされたのかは、心を揺さぶる。

fpv camera placement is wrong but overall a quick build

fpv camera placement is wrong but overall a quick build

fpv camera placement is wrong but overall a quick build