jaiger
Q: when will you have it in stock?
Asked by jaiger on 2019-12-23 08:36:08
efocentral HAS HOW TO SEND BLACK?
2020-06-15 07:53:58 Helpful (3)Q: which size is the practice lock?
Asked by BG163621356 on 2022-08-15 04:37:48
jaiger I'm not sure what dimensions you are looking for so I will do my best to describe the practice lock: the KEY tube outer dimension is 9.4mm. There are seven pins in my practice lock. The overall length or depth of the lock is 35mm including body and shaft. the lock body is 21.5mm diameter and 22.5mm deep. the lock shaft is 7mm diameter. I hope this helps. -Joe
2022-08-16 03:52:23 Helpful (0)
jaiger I've been using 1S batteries like eachine brand.
2022-08-08 08:15:41 Helpful (0)Q: are these CW, CCW or one of each?
Asked by jaiger on 2022-08-05 03:36:36
BG951533325 They'll rotate either direction depending on how you connect the leads to the ESC.
2022-08-05 08:43:41 Helpful (0)Q: can this send video directly to android?
Asked by chiZm on 2022-04-04 02:48:23
jaiger You can view the video from this camera on android if you have (1) a receiver device that connects to your android (like Eachine ROTG01) and (2) a video viewing app on the android phone.
2022-04-04 09:20:14 Helpful (0)Q: what is the rim (without tire) outer diameter and width?
Asked by LangersUK on 2022-02-05 03:29:41
jaiger I measure mine about 53mm diameter at outer rim and about 27mm depth or width. I just built a Tamiya TT02 rally model today. These rims fit it nicely on the car. they are about the same dimensions as the stock rims. I put the TT02 rally tires on these rims and they fit perfectly.
2022-02-05 07:26:16 Helpful (1)Q: Is there an option for a 3 blade prop if it comes with 2 blades??
Asked by BG249461104 on 2022-01-16 10:11:44
jaiger I use the prop that it came with.
2022-01-16 08:56:19 Helpful (1)
jaiger I made this mod and confirm it works with this camera. I followed the YT videos to identify pins to cut and splice. the soldering was tight and fragile but it works for OSD yes.
2021-11-24 10:43:14 Helpful (1)Q: can this be used on a Anet A8?
Asked by Wa22a on 2021-10-24 07:06:05
jaiger NOTE: I do not have an Anet A8 so I cannot answer authoritatively. I have used this on my TEVO Tarantula PRO. If your Anet A8 has capability to use BLTouch then this should work for you. Do you have connection on the motherboard? does the firmware support BLTouch? Do you have a place to mount it on the hot-end carriage?
2021-10-25 04:47:20 Helpful (1)Q: Is there speed control ESC onboard?
Asked by BG181618431 on 2021-08-12 12:14:27
jaiger No ESC onboard. I have this connected to my FC and the FC is connected to the ESC on my quadcopter.
2021-08-12 03:48:54 Helpful (0)
jaiger mine arrived last night and yes it comes with tension rods pre-installed. It looks like they can be removed using a set screw but I haven't tried that yet.
2021-07-29 08:16:36 Helpful (1)Q: Is this version I'm about to buy the one with the center tention rods?
Asked by BG621037371 on 2021-07-27 01:20:21
jaiger Mine arrived last night and yes it has the center tension rods pre-installed.
2021-07-29 04:53:35 Helpful (0)Q: Will these work with the Eachine Wizard X220s? If so, would it just be a matter of pairing the two?
Asked by Don Barbieri on 2021-07-12 02:02:38
jaiger Hi Don, The answer to your question is YES provided the Wizard is equipped with a 5.8Ghz analog FPV camera transmitter - then all you need to do is set the camera transmitter to same frequency or channel as the goggles. According to Eachine website, the Wizard FPV version will be compatible as it uses a 5.8Ghz transmitter.
2021-07-12 04:14:29 Helpful (1)Q: what polarisation is the antena
Asked by D0nt g3t Add1ct3d on 2021-04-07 11:40:50
jaiger Description says Antenna: 4 lobe right hand circular polarized
2021-04-07 01:00:50 Helpful (0)
jaiger This headset is a video receiver and display in one unit. Technically this unit connects with a video transmitter over the air typically in FPV use-case. While I haven't used px4 myself, I understand it is a flight controller - not a video transmitter. That said, I'm sure the PX4 flight controller can be used in an airframe (complete FPV quadcopter) that has a video transmitter connected to this headset. This headset will be one component in your total kit but it will not connect directly to the PX4. you need other components to make a complete system.
2021-03-05 08:54:22 Helpful (0)Q: Is it compatible with the Baofeng UV5 R walkie talkie
Asked by BG461719341 on 2021-02-08 12:39:46
jaiger Yes, I use it with my UV5R handhelds.
2021-02-08 10:10:19 Helpful (0)
jaiger I'd say about 0.75 turn - less than a full revolution.
2021-01-12 06:55:41 Helpful (0)Q: It's ok if i put it on my WPL C14?
Asked by Ubazz on 2020-11-29 05:10:14
jaiger Hi Ubazz, I had a C24 and the battery connector I remember was different from this battery. You will at least need a cable adapter to use this battery with your C14.
2020-11-29 06:57:33 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
jaiger yes you can
2023-01-10 07:11:10 Helpful (0)