Hobbyboy
mon contenu
Tous les messages
Commentaires
Commentaires
réponses
Questions

Tous les messages

Hobbyboy Nemox once a servo gets under 5g you will not find HV. high voltage for a 5.6g is 6v. I think Bluebird or BlueArrow servos have hv at 7.4v I think. If you find some let me know

nemox 25/02/2016
This servos work fine on 4.5 - 5.5V, when is voltage 5.5 to 8.4 servos trembles. I tested on servo tester and receiver Frsky X6R with Transmitter Taranis X9E with the same result :-( I needed HV micro servos.
JX Servo DHV56MG 5.6g DS Digital Coreless MG Engrenage Métallique HV Servo 1.2kg 0.10sec Pour Avion RC
US$8.00 US$17.99
7
Commentaires (3)

Hobbyboy 1kclc these work great! I've been using them for a few years now. Not to many 5g all metal gear servos on the market at this price range

1kclc 23/10/2017
I am using these on a WL V 950 helicopter to replace the stock servos. Had to replace the end connector and make shims under the servo. It is slightly smaller than original by about 1 to 2MM. works fine, will see how durable they are with the metal gears.
JX Servo DHV56MG 5.6g DS Digital Coreless MG Engrenage Métallique HV Servo 1.2kg 0.10sec Pour Avion RC
US$8.00 US$17.99
2
Commentaires (1)
Hobbyboy 13/07/2022
I finale got the replacement in as the 2nd unit osd chip or something when. This is a great board from what I've read. The board is delicate and you need to make sure you don't have and solder joints. So on this Fc I cut down the pin end so they are almost flush. I spread Flux on the pins this time not the board. The solder will flow! Next instead of soldering long leads. I soldered a xt60 directly to the board. I also soldered a separate power lead for cam/vtx as they are both above 5v operating power. Next I solder another xt60 to the esc side for a PnP fc. Keep in mind again this fc is sensitive solder quick and don't leave the tip sitting too long.
Contrôleur de vol Lefei Sparrow 2-OSD avec stabilisation gyroscopique Retour à la maison Support SBUS PPM PWM IBUS CRSF pour avion RC
US$32.50 US$59.99
1
Recommandations
Commentaires (2)

Hobbyboy hammer at work!

Hobbyboy 13/07/2022
I finale got the replacement in as the 2nd unit osd chip or something when. This is a great board from what I've read. The board is delicate and you need to make sure you don't have and solder joints. So on this Fc I cut down the pin end so they are almost flush. I spread Flux on the pins this time not the board. The solder will flow! Next instead of soldering long leads. I soldered a xt60 directly to the board. I also soldered a separate power lead for cam/vtx as they are both above 5v operating power. Next I solder another xt60 to the esc side for a PnP fc. Keep in mind again this fc is sensitive solder quick and don't leave the tip sitting too long.
Contrôleur de vol Lefei Sparrow 2-OSD avec stabilisation gyroscopique Retour à la maison Support SBUS PPM PWM IBUS CRSF pour avion RC
US$32.50 US$59.99
1
Commentaires (2)
Hobbyboy 19/03/2024
finally got me a Reptile Dragon 2. I've been wanting one since they first came out. I wasn't a fan of the price when it first hit the market, so I waited. In the box, you will find all parts are bubble wrapped. I removed everything from the box and did a dry fit, as you can see in the 2nd picture. The manual, as with many, is very limited in detail instructions. After watching a few videos, I think I will pass on the Vtail as it has x2 tail configuration. Everyone that video review this bird said the Vtail doest work well. The tail section is held on with four screws, and the nuts have already been glued in place inside the fuse at the attachment point. I didn't like the wood floor pieces that came with the kit. There is no recess for the two pieces and nothing in the manual. These pieces should've been cut to fit tight inside the fuse. This i a miss for me, and Reptile RnD should've fixed that issue. I'm going to mod the standard tail so it can be bolted together rather than gluing it together. This will help with transporting it, and if I ever re-sell it in the future, it will make it easier to pack up for shipping. I've already started the build by gluing the inner wing joints on first. I'm using gorilla glue white to assemble this bird. Fyi, at all the glue joints, make sure to sand both ends and wipe them down with denatured alcohol as this planes has excess mold release wax, which won't allow the glued to bond the foam pieces.
REPTILE DRAGON-2 Envergure de 1200mm Moteur Double Double Queue EPP FPV Avion RC KIT/PNP
US$139.90 US$231.59
0
Recommandations
Commentaires (0)
Hobbyboy 11/03/2024
These small brushless whoops are fast and can take a beating. I broke the battery mount and the Mobula7 wasn't flying right. Quick fix bought another Frame. Super easy to swap things over.
Kit de pièces de rechange Happymodel Mobula8 pour châssis Whoop de 85mm sans balais pour drone FPV de course
US$3.99 US$6.99
0
Recommandations
Commentaires (0)
Hobbyboy 11/03/2024
bought these to keep wirelooms inplace as I like to run them through bulkheads and such.
50pcs Bagues protectrices en caoutchouc pour câbles, diamètre interne de 5/6/7/8 mm
US$0.49 US$4.43
0
Recommandations
Commentaires (0)
Hobbyboy 11/03/2024
bought to clean up wires inside model planes
20pcs Passes-câbles en caoutchouc Protecteurs de câble en anneau Diamètre interne de 5/6/7/8mm
US$0.29 US$2.99
0
Recommandations
Commentaires (0)

Hobbyboy When setting up a plane with a Gyro. you need to plug in and leave the plane alone. Don't move it or try not too. Any gyro needs time to center itself. Also check the push rod and servo control horn. it could be hitting something or to tight. Some servos jitter because of feedback from the rx or interference.

BG171941104 05/09/2023
bonjour, petit problème avec le gyro. l'avion bat des ailes gauche droite ! pas stable !
XIAXIU Raptor H650 Air Terre Mer Envergure de 490mm 2,4GHz 6CH Avion RC en EPP Équilibrage Intelligent Warbird Fighter Hydravion RTF Pour Débutants
US$139.99 US$199.99
0
Commentaires (1)

Hobbyboy I've been using Jx servossince they came out. I have never had any issue with these servos. I've used Them in chuck gliders, lidl gliders and a bunch of scratch build planes. I have never had an issue!

MrMarek 19/05/2016
You can buy much better servos for 8 USD/pc. This is little servo with less power and really slow! I got 3 pcs and I'm not happy about. Just cheap.
JX Servo DHV56MG 5.6g DS Digital Coreless MG Engrenage Métallique HV Servo 1.2kg 0.10sec Pour Avion RC
US$8.00 US$17.99
3
Commentaires (1)
Hobbyboy 21/06/2023
After watching tracking for a few days. I got fed up because the package stopped moving, or should I say the tracking did. Needless to say, it's a pain that tracking doesn't follow the package all the way. So let me say this, it's cute! Nice size little wing, and I'm hoping performance exceeds its sleek look. Assembly is straightforward, and soldering is easy when you have a huge bay like this to work with. Remember to make everything easily disconnectable from the fc if you use one. It's small enough that you don't need one. The only glue I used were on the winglets, and it would be nice if they too were removable. I like the channels molded in the wing halves. Makes running cable and servo leads a "Snap! So far, this wing hasn't missed a beat. Has everything you need for good separation of the vtx with the pockets out on the wing. a hole for passing the antenna through would have been nice, but I'm not complaining at all. If you have all your parts, you can be up in the air in a few hours. Seriously, it's a breeze to get everything in and set up. Other than not having a place for the gps, I like it a lot! The only real head scratcher I could find was Elevon's. You will notice a gap that shouldn't be! Every other SonicModels plane has a molded in hinge line, no gaps. This little guy does, and I'm hoping some black packaging tape will work, as the elevon LE isn't beveled. That's it, nothing more I can say until I have maiden it successfully.
Sonicmodell Baby AR Wing Pro Envergure de 682mm Aile en EPP Avion RC Aile Volante FPV KIT/PNP
US$79.99 US$129.99
4
Recommandations
Commentaires (0)
Hobbyboy 24/01/2022
Bought this little gem because I wanted something small and lightweight. The goal here is to mod this little P-47 with a brushless motor direct drive no gear box. First thing I notices was the detail and the fitment of parts. The second thing I notice was the epp it's the soft white epp which should survive in a crash give how light it is. Mod video will soon follow so stay tuned! The only down side to this little warbird my parts showed up just wrapped in foam and put inside a shipping bag! Should've been in a box! I will contact BG costumer service for a replacement. Note: It did arrive before the arrival date which was February 2 2022
Pièces de rechange d'origine et accessoires pour l'avion RC Eachine Mini P-47 de 500 mm : récepteur, hélice, train d'atterrissage, servo moteur, interrupteur vertical, câble de charge, tige, autocollant, fuselage, aile
US$1.59 US$9.99
1
Recommandations
Commentaires (6)
Hobbyboy 06/07/2020
Great looking jet type plane, and assembles very easily. Has plenty of room for all your gear with room to spare. Finding the cg is simple and yeilds good results. I mounted a MicroDan 2510 2300kv motor and a 100a redbrick esc. I used Jx 9g servo's for control.
Stinger T750 Envergure de 750 mm Aile Delta de Course de l'Avion RC KIT Seulement
US$79.99 US$195.99
3
Recommandations
Commentaires (0)

Hobbyboy either heat the casing are the wire, or nuy some Ez-rod from Du-bro. Now that pushrod and guide tube flexes easy enough

BG239534655 09/08/2023
The control wire from the servo to elevator is an impossible connection. The wire is covered with a guide tube, which is too stiff to make the required turns to get to the elevator. There are no instructions, only the drawing.
JWRC Griffin Planeur RC en bois de balsa avec envergure de 1055mm Kit d'entraînement
US$36.00 US$59.99
0
Commentaires (3)
FIMI Manta 700mm Envergure VTOL Décollage et Atterrissage Verticaux Conception de Libération Rapide Compatible avec le Firmware Open-Source ArduPilot Avion RC FPV EPP PNP
US$149.00 US$199.99

Q: What kind of flight controller and esc will be used in the PNP with Flight Controller

demandé par McTechi sur 2023-08-02 03:39:02

Hobbyboy F405 fc installed

2023-08-31 03:08:55 Utile (1)
Soumettre
réponses (3)
Avion de Lancer à la Main de Grande Taille de 48 cm Avion en Mousse Inertielle EPP Bricolage Jouet pour Enfants
US$5.99 US$19.99

Q: Is the BLUE plane in the first photo real?

demandé par apoormarksman sur 2018-06-14 01:10:59

Hobbyboy Yes, they are both real!

2023-08-31 03:07:41 Utile (0)
Soumettre
réponses (8)
FIMI Manta 700mm Envergure VTOL Décollage et Atterrissage Verticaux Conception de Libération Rapide Compatible avec le Firmware Open-Source ArduPilot Avion RC FPV EPP PNP
US$149.00 US$199.99

Q: Ist das System crossfire tauglich ? fehlen quasi nur empfänger und funke ?

demandé par Evin123 sur 2023-08-13 03:27:30

Hobbyboy Yes! all rc are crsf compatible

2023-08-31 03:06:49 Utile (1)
Soumettre
réponses (1)
Hobbyboy 06/08/2019
The Cheetah glider is Awesome and feels lightweight and solid. I think the polihidral wing will add greatly to its stability in the air, as it gliders good and tracks straight. My conversion (2) 12g servo's (2) 5g servo's 12A Afro esc, and T-Motor 1804 14 2300kv motor. control Frshy X4R rx. already have motor mounted and plan on installing Cf rods to stiffen main wing. I dug out as much foam as i could from the cockpit area, and back under the wing. Mounted vtx under/ inside the canopy as it has plenty of room for vtx and cam. This is going to be a great glider once im done.
Avion en mousse EPP à ailes fixes de 100 cm d'envergure lancé à la main, jouet d'avion de course DIY
US$18.46 US$36.92
19
Recommandations
Commentaires (4)
Hobbyboy 10/08/2022
So my T-1 Ranger showed up today a few days late, but who's counting. The grey foam is way better than the white, while the white is lighter. The grey foam just feels better. Follow instructions online for an easy build. I plan on doing a Vtol conversion on this, which is why I bought the kit. All in all I'm satisfied mostly because I caught this on sale for $69 a few weeks back. Now to fins a suitable Fc that can handle Arduplane.
HEE AILE T-1 Ranger Envergure de 730mm Double Moteur EPP FPV Racer Avion RC Aile Fixe KIT/PNP
US$109.00 US$199.99
2
Recommandations
Commentaires (0)
ATOMRC Espadon 1200mm Envergure Double Moteur EPP Planeur FPV Avion RC Aile Fixe KIT/PNP/FPV/RTH/RTH+FPV
US$199.99

Q: Do you offer the RTH/FPV

demandé par BG476204355 sur 2023-06-02 04:21:19

Hobbyboy BG has either te kit or PnP version

2023-07-29 07:31:49 Utile (0)
Soumettre
réponses (1)

Vous êtes l'expert, pouvez-vous aider?

Nous vous invitons sincèrement à vous abonner à l'e-mail d'invitation à répondre!

Si vous vous abonnez, nous vous inviterons par e-mail à répondre aux questions des gens sur les produits. En vous abonnant, vous gagnerez également le «Badge utile»! Vous pouvez vous désinscrire à tout moment sur la page des paramètres de confidentialité.

Aidez les autres et soyez plus heureux!

  • S'abonner

À propos des badges

Les badges sont liés à la communauté et les utilisateurs le font en créant un contenu de qualité, en complétant des missions ou en participant à des activités spéciales. Les personnes spécifiques auront également leur propre badge exclusif.
Badge du PDG

L’insigne du PDG appartient uniquement au patron de Banggood.

Les badges que vous pouvez gagner arrivent bientôt
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe