Eachine Beecore F3_EVO_Brushed Flight Control Board For Inductrix Tiny Whoop Eachine E010 E010S Reviews - Banggood Online Shopping

Eachine Beecore F3_EVO_Brushed Flight Control Board For Inductrix Tiny Whoop Eachine E010 E010S

US$28.99
~~US$34.99~~
Buy now

Customer Reviews

4.88 out of 5

See all 758 reviews

5 star
697 (92.0%)
4 star
40 (5.3%)
3 star
12 (1.6%)
2 star
6 (0.8%)
1 star
3 (0.4%)

Write a Review Get double review points if you are one of the first 3 reviews published!

All Reviews (758)
Image (97)
Video (21)
All Star
- All Star(758)
- 5 Star(697)
- 4 Star(40)
- 3 Star(12)
- 2 Star(6)
- 1 Star(3)

Sort by:

Top Review

Top Review
Most Helpful
Most Recent

Reviews only from your country (United States)

|

Show Original

A part of the review has been auto-translated.

AaronVIP1
US
19/01/2017

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!
48

Comments (4)

Show Original
igyigyVIP1
US
17/11/2016

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight
18

Comments (2)

Show Original

Show:

Total 0 pages

Go to page

Go

You might be interested in

recommendation for you