Grandpa
mis contenidos
Todos los mensajes
Comentarios
Comentarios
respuestas
Preguntas

Todos los mensajes

Grandpa 25/08/2022
I was a bit unhappy at first as I was not able to download the manual and my unit arrived with a cracked case. I began to investigate it and repair it. The instructions available on the sales page provided enough information to set the unit up and running some tests. The unit works better than I had expected. I was able to determine the frequencies used. Low = 62 Hz Med = 234 Hz Med 2 = 2 kHz and High = 14.5 kHz. The red knob selects one of 4 different internal resistances. The A/B push button turns on and off the dual channel mode so that you can easily compare one circuit board position to another. The Blue knob adjusts the position of the "B" Channel image on the scope screen. I added a power switch to the unit so that it could be left plugged in when I wanted to. I also added some English Labels and non-slip feet for the back so that it doesn't slide around on the bench. The only item I have not been able to identify is a Blue Jack on the front that is labeled "G" on the front and "T" on the internal board. If anyone has figured what the "G" Jack is please let me know. I wrote a complaint to Banggood about the inability to down load the Manual and about a week later they sent me the pdf file. Unfortunately it did not identify the "G" jack. Over All I am very pleased with the unit and the way it functions. I would recommend it to anyone who has a curiosity about curve tracers and a scope capable of X-Y operation.
Probador de curva VI de doble canal, mostrando 2 formas de onda al mismo tiempo para una fácil comparación
US$34.99 US$45.99
4
Recomendaciones
Comentarios (2)
Grandpa 01/07/2022
I was very satisfied with these batteries. Unlike many brands the Nominal rating of 3000 mAhr was accurate. When I ran a power test I got a reading of 2920 mAhr. The batteries also weigh a little more than many of the batteries that are being sold. The batteries from this order were about 46 gm. I felt it was a very good buy and I will buy more in the near future.
4Pcs Astrolux® C1830 3000mAh 3.7V 18650 Batería de litio recargable no protegida Li-ion Célula de potencia de 9.6A de alto rendimiento para linternas Nitecore Lumintop Fenix Olight RC Toys
US$27.99 US$29.99
0
Recomendaciones
Comentarios (0)
Grandpa 29/07/2020
OK
3 piezas Sensor de Efecto Hall LM393 3144 Módulo de Sensor de Efecto Hall para Coche Inteligente Geekcreit para Arduino - productos que funcionan con placas Arduino oficiales
US$5.99 US$7.99
0
Recomendaciones
Comentarios (0)
Grandpa 29/07/2020
OK
Juego de dados electrónicos con protección de conexión inversa LED Dados DIY Piezas electrónicas
US$6.99 US$8.99
0
Recomendaciones
Comentarios (0)
Grandpa 29/07/2020
OK
DIY NE555 Kit de módulo de timbre Ding Dong Bell Kit de entrenamiento de producción electrónica de música DIY DIY
US$2.49 US$2.99
0
Recomendaciones
Comentarios (0)
Grandpa 29/07/2020
OK
Estacionamiento por infrarrojos Sensor Kit Recordatorio de velocidad de marcha atrás por infrarrojos Placa de circuito electrónico PCB Producción DIY Kit
US$7.99 US$9.99
0
Recomendaciones
Comentarios (0)
Grandpa 29/07/2020
If you have purchased this kit to test or improve your soldering skills do not be too hard on yourself. The traces on the circuit board are very fragile. I have years and thousands of hours of soldering experience and I had to repair 4 traces that broke while the unit was being assembled. The slightest torque on any of the components or LEDs causes the trace to lift from the board and break. Use a continuity meter to test your traces if the unit doesn't work and then use clipped leads to jumper across the breaks in the traces. You can't beat the price so forgive yourself on this one if it does't work right out of the gate. Also be aware that CCW on the trimmer increases sensitivity and CW decreases the sensitivity.
LM3915 Kit de indicador de nivel de audio de 10 segmentos Electrónico Soldadura Experimento de entrenamiento DIY Piezas
US$2.99 US$4.49
0
Recomendaciones
Comentarios (0)
Grandpa 29/07/2020
OK
Kit de 3 dados electrónicos con protección de conexión inversa, dados LED para bricolaje, piezas electrónicas
US$6.25 US$7.50
0
Recomendaciones
Comentarios (0)
Grandpa 29/07/2020
OK
Diy toque vibración alarma kit electrónico de formación de enseñanza
US$2.99 US$3.99
0
Recomendaciones
Comentarios (0)
Grandpa 07/02/2020
I am quite pleased with this power supply control board except for one problem. The circuit is designed to use (3) TL081 Op Amps which have an Offset circuit built in. The Offset is necessary in the U2 position (lower right hand corner above the blue trimmer) if you want to bring your voltage to zero volts when the voltage control is all the way down. Unfortunately the TL081 chips that are currently being supplied with the kit are not quality and they do not have the Offset circuitry built into the chip. If you want to be able to zero your voltage output when the voltage control is all the way down you will have to purchase a quality TL081 chip for this position. At the price they are selling these kits for this is a small problem and easily remedied. John
Módulo de Fuente de Alimentación Regulada Ajustable de CC de 0-30V 2mA - 3A Kit de Bricolaje
US$4.99 US$9.59
0
Recomendaciones
Comentarios (0)
Grandpa 23/01/2019
I have ordered these M-Testers a couple times and I have generally had good luck with them. The plastic cases make them a lot more usable and attractive. This batch however had one unit that didn't work properly. Looks like the Atmel chip is defective but at the cost per unit it is no problem.. I will use it for spare parts. A second problem with each unit seemed more serious. The test socket contacts would not open all the way. After removing the sockets from the board and checking them out I found that they worked just fine once they were removed from the board. The source of the problem was that the sockets had been soldered to the board by the manufacturer while in the closed position. This holds the contacts to one side and when the socket is soldered the solder holds the pins towards the closed side and doesn't allow them to open. The solution if you are having this problem is to simply open the test socket and heat up the solder to each pin to allow the pin to come to its normal open position. John
Geekcreit® LCR-T4 Mega328 Probador de transistores Diodo Triodo Capacitancia Medidor ESR Con carcasa
US$9.99 US$21.99
0
Recomendaciones
Comentarios (1)
Grandpa 15/10/2018
These buttons are momentary, not latching! The information supplied is contradictory as it states both latching and momentary. They are also small like the typical small key switch with an LED under the button.
Interruptor de enclavamiento del símbolo de alimentación luz LED Botón pulsador SPST
US$6.99 US$8.99
0
Recomendaciones
Comentarios (0)
Grandpa 27/09/2018
This is a normally open momentary switch.
Wendao R13-507 125V 6A 16mm No cerradura Botón de reinicio automático APAGADO/ENCENDIDO 10 piezas
US$13.99 US$16.99
0
Recomendaciones
Comentarios (0)
Grandpa 26/07/2018
I was a little surprised by how small the cutters were, only 3.75 inches from pointed tip to end of handle but they cut very well and were well machined. I was able to cut typical leads at the very tip of the jaws with no problems. The small size may even be an advantage. John
DANIU Mini Alicate de mano - Alicate de corte diagonal - Alicate pelacables - Cortadores de cables eléctricos
US$3.59 US$9.99
0
Recomendaciones
Comentarios (0)

Grandpa Sorry I missed your question earlier. 24cm wide X 9 cm high X 26 cm deep with approx 4 kg.John

Grandpa 29/08/2017
This is a very versatile and useful basic power supply circuit. So far I have used it to build several dual bench power supplies and other specialized test equipment. Lots of fun.
Módulo de Fuente de Alimentación Regulada Ajustable de CC de 0-30V 2mA - 3A Kit de Bricolaje
US$4.99 US$9.59
7
Comentarios (2)
Grandpa 11/04/2018
I think this is the nicest little meter I have ever owned. It has features and accuracy found on meters 10 to 20 times more expensive. It even has an EM field detector so you can tell when a conductor is hot with lethal voltage. The only problem I had is that one of the internal fuses had popped out of its clips during shipping so I had to open the case and put it back in place. John
Multímetro Digital MUSTOOL MT66 True RMS 5999 Cuenta AC/DC Probador de Voltaje Corriente
US$20.13 US$24.16
0
Recomendaciones
Comentarios (0)
Grandpa 21/03/2018
I bought 5 of these and they are working great. My 11 year old grandson built one the other day and it turned out good after we discovered he had switched one 8550 with an 8050. It is nice when a mistake like this doesn't cause anything to burn up. After putting things where they belonged it worked well. We mounted it on a 6 volt battery box with a power switch and he had a nice little project to show at school.
5Pcs Dados Electrónicos DIY Kit 5mm Rojos LED Piezas Interesantes NE555 CD4017 Producción Electrónica
US$13.99 US$16.99
0
Recomendaciones
Comentarios (0)
Grandpa 21/03/2018
As noted by other reviewers the circuit doesn't work well as designed but I do not agree with them as to how to fix it. R-2 39K has the purpose of introducing hysteresis into the circuit, however it creates way too much and extreme temperature moves are necessary to make it work. Just changing R2 from 39K to 100K brings the hysteresis down to 4 degrees C. The LED should have a current limiting resistor and there is a problem with Q1 overheating if the transistor is turned on to saturation by the variable resistor. Keep the variable resistor away from the 0 ohms end of its travel. This circuit was a lot of fun since it didn't work and took some study and experiment to make it function. For the price I had a lot of fun.
Control de temperatura Kit de alarma de luz de sonido Circuito electrónico DC3-5V DIY Training Suite
US$2.43
2
Recomendaciones
Comentarios (1)

Usted es el experto, ¿puede ayudarme?

¡Te invitamos sinceramente a suscribirte al correo electrónico de respuesta de invitación!

Si se suscribe, lo invitaremos por correo electrónico para que responda las preguntas que la gente tenga sobre los productos. ¡Al suscribirte, también ganarás la "Insignia útil "! Puede darse de baja en cualquier momento en la página de configuración de privacidad.

¡Ayuda a los demás y sé más feliz!

  • Suscribir

Sobre insignias

Las insignias están relacionadas con la comunidad, y los usuarios obtienen insignias creando contenido de calidad, completando misiones o participando en actividades especiales. Las personas específicas también tendrán su propia insignia exclusiva.
Insignia del CEO

La insignia del CEO es propiedad exclusiva del jefe de Banggood.

Las insignias que puedes ganar llegarán pronto
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe