Alle meddelelser

georget 22/09/2019
I purchased the Enusic battery charger mainly because I wanted to experiment with the Pulse Repair mode. The idea is that it will send low and high frequency pulses into the battery and help break down the sulfate that builds up on the plates over time. This sulfate build up can weaken a battery so removing it sounds good to me. I have used the Pulse repair on several batteries. It may take several hours depending on size and condition of battery, but eventually the Pulse repair will finish and turn OFF. If I wait a few minutes, and try the Pulse repair again on the same battery, it will run for a few seconds, then turn OFF so it must have done something that the charger can measure. Very cool! This charger has an internal fan that turns on when in Pulse repair mode. In the video, I use an oscilloscope to show what the output of the charger looks like when in Pulse Repair mode and disconnected from the battery. The voltage level shifts between 8 volts and 14 volts every second. It also has 25 kilohertz high frequency pulses measured from rising edge to rising edge. When the charger is connected to a battery that is already charged, you will not see the voltage level shift down to 8 volts on the oscilloscope. You will still see the 25 kilohertz high frequency pulses. The charger has a LCD display that shows voltage, current, and percentage of charge in the battery. It also has a motorcycle mode that limits the current to 1.5 amps. In the normal Vehicle mode, the current has a max of 8 amps. As the battery charges up, you can watch as the current draw goes down. When the battery is fully charged, it switches to OFF. So far, I like this charger a lot. If you have any experience with it, please add your comments to my YouTube video below... https://youtu.be/TLdoGV_QEuY
29
anbefalinger
Kommentarer (2)

Q: is this compatible to nissan navara np***** model?

spurgt af BG036491347 på 2021-09-09 10:20:06

georget Does the 2017 Nissan Navara np300 have a OBD2 connector?

2021-09-09 12:32:11 Nyttig (0)
Indsend
svar (1)

Q: is this compatible for Toyota vios 2005?

spurgt af BG314474717 på 2021-08-25 02:17:59

georget Does your 2005 Toyota Vios have a OBD2 connector?

2021-08-25 07:17:54 Nyttig (0)
Indsend
svar (3)

Q: does this model supports 99 Toyota camry?

spurgt af BG536171144 på 2021-05-16 02:27:02

georget If your car has a OBD2 port, the scanner should be able to read some data.

2021-05-16 04:39:09 Nyttig (0)
Indsend
svar (4)

Q: What is the weight of the box

spurgt af silvabryan960 på 2019-11-19 11:42:36

georget Sorry

2021-04-08 08:38:20 Nyttig (0)
Indsend
svar (2)

Q: is it have one colour

spurgt af Murali Kp murali på 2019-03-30 01:49:53

georget These are RGB LEDs so you can change the color.

2021-04-08 08:35:53 Nyttig (0)
Indsend
svar (4)

Q: how about weight?

spurgt af incxbxs på 2018-11-23 05:52:44

georget The weight of the device is only around 1 pound US since it is made of hollow plastic. You may want to add weight to the base for a more stable device.

2021-04-01 08:21:21 Nyttig (0)
Indsend
svar (6)

Q: Does it have inner mounting holes for placing pcb inside?

spurgt af Vitocolr på 2018-02-19 03:43:49

georget Yes see customer photos.

2021-04-01 08:16:42 Nyttig (0)
Indsend
svar (2)

Q: Theo power suply its inclused?

spurgt af Catulo på 2021-03-31 07:24:39

georget 12V Adapter NOT included

2021-04-01 08:14:47 Nyttig (1)
Indsend
svar (1)

Q: Does this unit work on Chinese Saic mg6?

spurgt af MSRAHBI på 2021-03-30 01:15:24

georget In 2008, the OBD2 standard became mandatory for all vehicles produced for the Chinese market.

2021-03-30 06:29:44 Nyttig (0)
Indsend
svar (1)

Q: How to get the product responsive? In Q

spurgt af ericluiijf på 2020-04-14 10:18:44

georget Connect Arduino to computer using USB cable and then run the Arduino IDE software.

2021-03-25 07:18:08 Nyttig (0)
Indsend
svar (4)

georget For three dollars, it probably does not have too much noise suppression inside. Give it a try and let us know.

2021-03-25 07:15:04 Nyttig (0)
Indsend
svar (2)