Raceflight Betaflight REVO F4 STM32F405 Flight Controller with Vbat/Buzzer for RC Drone
En del af anmeldelsen er automatisk oversat.
This F4 FC is the cheapest one i've ever seen. It's quality is good too!! Please Upload Airbot F4 Hex while uploading the firmwares. First install the STM32 drivers(http://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-utilities/stsw-stm32102.html) and ZADIG(http://zadig.akeo.ie/). Then make sure you enter the flashing mode by holding the Boot Button on the bottom left and powering up the FC. The Configurator(Raceflight/Betaflgiht) should show DFU as seen in the pics. For betaflight, do as you see in the picture. For raceflight download (https://raceflight.net/rf1beta/revolt222.bin) and load the firmware(OFFLINE LOADING).You can even use the blackbox(onboard flash), by enabling it from the configurator, and then reading back from the blackbox viewer (https://github.com/betaflight/blackbox-log-viewer). :)
Контролер сильно греется , Проблем с прошивкой не возникло. При работе с REVO.HEX BF3.0.1 Не работали LedStrip пока не нашел другую схему подключения. Также сразу отвалилась верхняя часть кнопки BOOT
I got mine quickly (10 days). i flashed with RaceFlight Revo firmware released on october 13 2016 the big problem is the lack of instructions !!! especially for the power supply, the minimum would be to indicated the input port and the maximum voltage. a wiring scheme is absolutely necessary... so please do it !
cheapest F4 Chip on market. Works great with Betaflight and can easily handle 8kHz/8kHz. With onboard Voltage Regulator. Also tested with DShot 600 on Betaflight with Racerstar RS 30A V2.
I have received my board yesterday and I have managed to set it up and install it the same day. As mentioned before there is no wiring manual and although there is an info on rcgroups it is a long thread and it is hard to find how to wire configure the board. Here is a blog post that I have written regarding the board setup and configuration, I hope that you will find it helpfull http://lll.mk/multicopter/revo-f4-banggood-com-firmware-update-wiring-configuration/
Прошивать обязательно из под Raceflight , даже прошивками Betaflight. По прошивкам , если регули поддерживают DSHOT , то прошивать прошивку Airbot F4 , если регули НЕ поддерживают (например FVT 20A Opto), то прошивку REVO F4 . Это важно , иначе будет куча глюков и регули-моторы могут не работать.
the boot button is gone :(. i se that is a problem
Не обратил внимания что нельзя подключить PWM сигнал, пришлось дозаказывать приемник с SBUS. При 8/8кгц и dshot600 4% загрузка проца.
Получил. Заказ шел месяц. Встроенный БЭК, быстрый процессор, но с прошивкой возникли проблемы. Не ставятся дрова, пробовал на 3х разных компьютерах. В итоге прошил при помощи адаптера, подпайкой проводов. Прошил не той прошивкой, без DSHOT, а коптер уже собрал, пришлось разобрать, прошить заново, опять паять, короче проблемный в плане прошивки. Летает. Проц не грузится, с акселерометром 4%. Если больше не шить, то норма.
Nice Raceflight Betaflight CC3D REVO F4 STM32F405 bord. Hope i can flash it to Raceflight.