I clipped the fragile ducts from my FB90's and replaced the anemic 40mm 4-blade props with 45mm tri-blades. The performance difference was amazing, but the thin frames didn't hold-up in crashes on grass. So I'm in the process of remounting those FB90 parts, including this flight controller, on more durable 2mm thick frames, with 55mm ladybird-style props and removable Kingkong guards (stabilized with dental floss) for indoor FPV and outdoor Freestyle/FPV. It's all plug-n-play thanks in large part to this flight controller design. I flashed the first to Betaflight 3.01 and ran about 20 Lipos through it in a combination of indoor and outdoor FPV freestyle including acro. This flight controller performed great, with only one split-second dropout (barely noticeable; stage 1 failsafe fallback) while flying with my FS-i6X transmitter. I also experienced a couple of repeatable, uncommanded flips during extreme cornering at high-speeds in 'angle-mode' using 70 degrees of pitch (which I'll attribute to inadequate PID tuning). I flew out to 80 meters several times without issue (the edge of the park) so I presume it could go farther. I dinged one star on 'quality' for the fragile mono-pole antenna (mounted without GND) and the micro-Losi connector as opposed to JST as is common for 2S (7.4V). But I have to say this is an amazing AIO flight controller for a good price! Flying 2S on a brushed micro is reinvigorating my interest in brushed quads....very impressed!!!

I clipped the fragile ducts from my FB90's and replaced the anemic 40mm 4-blade props with 45mm tri-blades. The performance difference was amazing, but the thin frames didn't hold-up in crashes on grass. So I'm in the process of remounting those FB90 parts, including this flight controller, on more durable 2mm thick frames, with 55mm ladybird-style props and removable Kingkong guards (stabilized with dental floss) for indoor FPV and outdoor Freestyle/FPV. It's all plug-n-play thanks in large part to this flight controller design. I flashed the first to Betaflight 3.01 and ran about 20 Lipos through it in a combination of indoor and outdoor FPV freestyle including acro. This flight controller performed great, with only one split-second dropout (barely noticeable; stage 1 failsafe fallback) while flying with my FS-i6X transmitter. I also experienced a couple of repeatable, uncommanded flips during extreme cornering at high-speeds in 'angle-mode' using 70 degrees of pitch (which I'll attribute to inadequate PID tuning). I flew out to 80 meters several times without issue (the edge of the park) so I presume it could go farther. I dinged one star on 'quality' for the fragile mono-pole antenna (mounted without GND) and the micro-Losi connector as opposed to JST as is common for 2S (7.4V). But I have to say this is an amazing AIO flight controller for a good price! Flying 2S on a brushed micro is reinvigorating my interest in brushed quads....very impressed!!!

I clipped the fragile ducts from my FB90's and replaced the anemic 40mm 4-blade props with 45mm tri-blades. The performance difference was amazing, but the thin frames didn't hold-up in crashes on grass. So I'm in the process of remounting those FB90 parts, including this flight controller, on more durable 2mm thick frames, with 55mm ladybird-style props and removable Kingkong guards (stabilized with dental floss) for indoor FPV and outdoor Freestyle/FPV. It's all plug-n-play thanks in large part to this flight controller design. I flashed the first to Betaflight 3.01 and ran about 20 Lipos through it in a combination of indoor and outdoor FPV freestyle including acro. This flight controller performed great, with only one split-second dropout (barely noticeable; stage 1 failsafe fallback) while flying with my FS-i6X transmitter. I also experienced a couple of repeatable, uncommanded flips during extreme cornering at high-speeds in 'angle-mode' using 70 degrees of pitch (which I'll attribute to inadequate PID tuning). I flew out to 80 meters several times without issue (the edge of the park) so I presume it could go farther. I dinged one star on 'quality' for the fragile mono-pole antenna (mounted without GND) and the micro-Losi connector as opposed to JST as is common for 2S (7.4V). But I have to say this is an amazing AIO flight controller for a good price! Flying 2S on a brushed micro is reinvigorating my interest in brushed quads....very impressed!!!

Muito boa, atualizei o Betaflight sem problema algum, recomendo muito. So tenho uma duvida, os conectores dos motores (SH) são mesmo de 1.0? Estou usando esta por ser integrada com um receptor FlySky em um mini drone race DIY

Muito boa, atualizei o Betaflight sem problema algum, recomendo muito. So tenho uma duvida, os conectores dos motores (SH) são mesmo de 1.0? Estou usando esta por ser integrada com um receptor FlySky em um mini drone race DIY

Muito boa, atualizei o Betaflight sem problema algum, recomendo muito. So tenho uma duvida, os conectores dos motores (SH) são mesmo de 1.0? Estou usando esta por ser integrada com um receptor FlySky em um mini drone race DIY

this FC could use 2s brushless motors which has much power than 1s motors. very stable and simple FC. it can power up camera, battery alarm. I used almost 2 years.

this FC could use 2s brushless motors which has much power than 1s motors. very stable and simple FC. it can power up camera, battery alarm. I used almost 2 years.

this FC could use 2s brushless motors which has much power than 1s motors. very stable and simple FC. it can power up camera, battery alarm. I used almost 2 years.

Very easy to setup, flashed it with Clean Flight tuned it and result was awesome. Very responsive!

Very easy to setup, flashed it with Clean Flight tuned it and result was awesome. Very responsive!

Very easy to setup, flashed it with Clean Flight tuned it and result was awesome. Very responsive!

I have build one of these as a QX90C 2s before and i love it. It is crazy fast but feels safer than the bigger quadcopter the flight controller is easy to work with due to the easy motor ports. Makes it easy to replace them if needed. Soldering points is small as expected. Adding buzzers and camera is not the easiest for novice soldering. My other problem might just be me but my quadcopter flips over at high throttle and does a big dive into the ground. I have changed the motors a few times over (thinking damaged motor) and my settings are exactly the same as my previous 2s. It just doesn't like the max power. As I have tried all options and it is built exactly like the other my only conclusion is that its the flight controller.

I have build one of these as a QX90C 2s before and i love it. It is crazy fast but feels safer than the bigger quadcopter the flight controller is easy to work with due to the easy motor ports. Makes it easy to replace them if needed. Soldering points is small as expected. Adding buzzers and camera is not the easiest for novice soldering. My other problem might just be me but my quadcopter flips over at high throttle and does a big dive into the ground. I have changed the motors a few times over (thinking damaged motor) and my settings are exactly the same as my previous 2s. It just doesn't like the max power. As I have tried all options and it is built exactly like the other my only conclusion is that its the flight controller.

I have build one of these as a QX90C 2s before and i love it. It is crazy fast but feels safer than the bigger quadcopter the flight controller is easy to work with due to the easy motor ports. Makes it easy to replace them if needed. Soldering points is small as expected. Adding buzzers and camera is not the easiest for novice soldering. My other problem might just be me but my quadcopter flips over at high throttle and does a big dive into the ground. I have changed the motors a few times over (thinking damaged motor) and my settings are exactly the same as my previous 2s. It just doesn't like the max power. As I have tried all options and it is built exactly like the other my only conclusion is that its the flight controller.

An excellent board, very well made but note the motor connections are 1.0mm sockets rather than the 1.25mm that are more commonly used. Goes well with the designed 2S Fat Bee motors though. Fitted in an Eachine QX100 frame and fitted with 230 mAH batteries gives 4 minute flight times with so much more punch than any 1S. Highly recommended.

An excellent board, very well made but note the motor connections are 1.0mm sockets rather than the 1.25mm that are more commonly used. Goes well with the designed 2S Fat Bee motors though. Fitted in an Eachine QX100 frame and fitted with 230 mAH batteries gives 4 minute flight times with so much more punch than any 1S. Highly recommended.

An excellent board, very well made but note the motor connections are 1.0mm sockets rather than the 1.25mm that are more commonly used. Goes well with the designed 2S Fat Bee motors though. Fitted in an Eachine QX100 frame and fitted with 230 mAH batteries gives 4 minute flight times with so much more punch than any 1S. Highly recommended.

But i have the identical 1s version, and that is all good so I was just unlucky I guess

But i have the identical 1s version, and that is all good so I was just unlucky I guess

But i have the identical 1s version, and that is all good so I was just unlucky I guess

good

good

good

i had some Problems to bind my fatbee. banggood resend me another FC for free, and the binding was no Problem. Thank you for the easy Support.

i had some Problems to bind my fatbee. banggood resend me another FC for free, and the binding was no Problem. Thank you for the easy Support.

i had some Problems to bind my fatbee. banggood resend me another FC for free, and the binding was no Problem. Thank you for the easy Support.

It does a really good job controlling the micro I have put together. The LED controllers didn't work as I expected, but everything else worked.

It does a really good job controlling the micro I have put together. The LED controllers didn't work as I expected, but everything else worked.

It does a really good job controlling the micro I have put together. The LED controllers didn't work as I expected, but everything else worked.