tin nhắn

RagTheNutsOff 2017-09-21 21:22:39
3
gợi ý
Bình luận (0)

Những người đánh giá hàng đầu bạn có thể thích:

RagTheNutsOff 2019-01-02 05:39:08
Firstly you've got to say it's obvious there has been a LOT of time & effort put into the design of the Dart XL. However the model has numerous issues and unless you fly at just one speed, you'll get bored of it quickly. The hose section is extremely weak. If you add two 4mm carbon rods either side the nose and also add a 4mm plywood base the model can then take a nose punt. The aerofoil has an obscene amount of reflex built into it, combine that with an incorrect thrust angle for the motor the model will just climb & climb. Even with 4mm of packers below the top two motor mounts, it still took 8mm of down trim for the model to fly level. You'll need to reinforce the motor mount as well as the amount of foam back there is lacking. Just throttle up with the rear lid off and watch the motor mount flex inwards. The complete list of issues are below, I'm sure ZOHD given their history will address these over time. I'm just amazed these were over looked in the reviews. - Thrust angle wrong out if the box - Motor mount flexible - No bands over clevises - Servos on the wrong side of the model (need to be top mounted) - No plastic covers for wing tips - Terrible inverted flying characteristics compounded by the amount of reflex in the model - FPV camera angles downwards - Nose likes to fall off - Nose is a poo scoop - Does not fit a session or runcam 3S - The 30A ESC is not up to 4S standards and I reckon that was a compounding issue with the servos not having enough current to move under load. So in summary, you are forced to fly this model at one speed, any more and it'll climb until it loops over on itself. A great attempt, but frankly wait until a version 2 is developed or just buy it because you like the look of it (a very valid reason!). Matt PS. I know the above maybe unpopular, however this was not a freebie that was sent to me for review.
24
gợi ý
Bình luận (1)

Những người đánh giá hàng đầu bạn có thể thích:

RagTheNutsOff 2019-08-01 04:17:52
0
gợi ý
Bình luận (0)

Những người đánh giá hàng đầu bạn có thể thích:

RagTheNutsOff 2017-09-09 06:58:04
9
gợi ý
Bình luận (1)

Những người đánh giá hàng đầu bạn có thể thích:

Q: This is too expensive for a foamy!

Được hỏi bởi mouse742 trên 2019-03-14 03:11:35

RagTheNutsOff Seriously $220 or £166!!! I think I'll pass at that price.

2019-03-14 04:56:53 Hữu ích (1)
Gửi đi
Đáp án (8)
RagTheNutsOff 2019-01-31 01:04:02
1
gợi ý
Bình luận (0)

Những người đánh giá hàng đầu bạn có thể thích:

RagTheNutsOff 2019-01-02 19:48:48
9
gợi ý
Bình luận (2)

Những người đánh giá hàng đầu bạn có thể thích:

RagTheNutsOff 2018-12-02 21:32:24
3
gợi ý
Bình luận (0)

Những người đánh giá hàng đầu bạn có thể thích: