Paulo
Q: Will two of these be able to provide enough thrust for a 1.5 kg airplane?
demandé par frederikedvardsen sur 2019-07-02 03:29:44
Q: Can anyone tell me how to turn off the green switch back-light?
demandé par Paulo sur 2019-04-15 11:23:20
Phrozin I honestly just give a quarter turn on tailcap to disconnect 100% and no parasitic drain from green light or electronics..,but the button presses as stated by other user will also work
2021-05-12 07:11:19 Utile (0)
Paulo No. it will display 4x the true RPM - no switch
2021-03-11 05:20:48 Utile (0)
Paulo These rods are for use with TIG welder, not gas torch.
2020-10-02 06:53:39 Utile (0)
Paulo No. There is no meter that can do this.
2019-11-20 12:52:02 Utile (0)Q: what’s the use of the two variable resistors
demandé par mustafa_alasair sur 2019-06-27 12:46:46
Paulo Here is a method to set up the charger controller - I found that the settings were not correct when the board was delivered to me. VR1 will change the voltage where the relay switch closes (The battery charger turns on) VR2 will change the voltage where the relay switch opens (The battery charger turns off) Turn the screw clockwise to reduce the setting and counter-clockwise to increase the setting. To set up the controller, do the following: First set the voltage that the charger will turn on: 1. screw VR1 fully counter-clockwise (maximum setting - approx 15 turns) 2. screw VR2 fully clockwise (minimum setting - approx 15 turns) 3. apply a voltage of 11.0V to the "+V-" terminals 4. adjust VR2 (counter-clockwise ) until the LED turns on (the relay switch closes to start the charging) Now set the voltage that the charger will turn off: 1. apply a voltage of 14.5V to the "+V-" terminals 2. adjust VR1 (clockwise) until the LED turns off (the relay switch opens to stop the charging) Now check that the settings are correct by varying the voltage applied to the "+V-" terminals The LED should come on when the voltage drops below 11.0V and the LED should go off when the voltage rises above 14.5V. If necessary, make small adjustments to VR1 and VR2 until the on and off voltages are correct to your requirements. Now connect your battery charger
2019-07-13 02:40:30 Utile (4)
Paulo Operating voltage: DC 11.5-14.5v, the highest can not exceed 15v, otherwise the chip will burn. Relay closed charging voltage: 11.5v - Adjust this setting with VR2 Relay off protection voltage 14.5v - adjust this setting with VR1 Voltage error: 0.1v Voltage detection mode: DC voltmeter - Connect volt meter to terminals "VCC and -" Charging type: 12v battery battery - Connect battery terminals to battery charger and "V "
2019-07-10 05:42:30 Utile (4)Nous vous invitons sincèrement à vous abonner à l'e-mail d'invitation à répondre!
Si vous vous abonnez, nous vous inviterons par e-mail à répondre aux questions des gens sur les produits. En vous abonnant, vous gagnerez également le «Badge utile»! Vous pouvez vous désinscrire à tout moment sur la page des paramètres de confidentialité.
Aidez les autres et soyez plus heureux!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Paulo Yes
2021-07-12 07:32:20 Utile (2)