Estava aguardando a placa na versão 1.0 mas, o rótulo mostra a versão 1-5. Creio não haver problema pois o layout é exatamente o mesmo. No geral, produto muito bom.

Estava aguardando a placa na versão 1.0 mas, o rótulo mostra a versão 1-5. Creio não haver problema pois o layout é exatamente o mesmo. No geral, produto muito bom.

Estava aguardando a placa na versão 1.0 mas, o rótulo mostra a versão 1-5. Creio não haver problema pois o layout é exatamente o mesmo. No geral, produto muito bom.

3D Printer Mainboard Anet V1.0 Motherboard - No auto level firmware installed. On arrival I had issues with theAnet A8 v1 motherboard. I contacted Bg and it was arranged very quick that a replacement was sent to me. Thanks BG - great service as always.

3D Printer Mainboard Anet V1.0 Motherboard - No auto level firmware installed. On arrival I had issues with theAnet A8 v1 motherboard. I contacted Bg and it was arranged very quick that a replacement was sent to me. Thanks BG - great service as always.

3D Printer Mainboard Anet V1.0 Motherboard - No auto level firmware installed. On arrival I had issues with theAnet A8 v1 motherboard. I contacted Bg and it was arranged very quick that a replacement was sent to me. Thanks BG - great service as always.

This part came well packaged and in working order. It appears to be an OEM replacement part with firmware already installed. The connectors on the board for the bigger power wires(green plastic), power in, heat bed, and extruder, were loose upon final inspection before install. I would recommend re soldering the connections or something to tighten them up,

This part came well packaged and in working order. It appears to be an OEM replacement part with firmware already installed. The connectors on the board for the bigger power wires(green plastic), power in, heat bed, and extruder, were loose upon final inspection before install. I would recommend re soldering the connections or something to tighten them up,

This part came well packaged and in working order. It appears to be an OEM replacement part with firmware already installed. The connectors on the board for the bigger power wires(green plastic), power in, heat bed, and extruder, were loose upon final inspection before install. I would recommend re soldering the connections or something to tighten them up,

Funguje jak má OK

Funguje jak má OK

Funguje jak má OK

Buena calidad. Original de Anet. Funciona perfectamente en la Anet A8

Buena calidad. Original de Anet. Funciona perfectamente en la Anet A8

Buena calidad. Original de Anet. Funciona perfectamente en la Anet A8

Bought this to replace my Anet A8 motherboard, works fine.

Bought this to replace my Anet A8 motherboard, works fine.

Bought this to replace my Anet A8 motherboard, works fine.

Layout of board much improved. Board, extruder and bed connectors now all of the same type and more sturdily soldered to the board. Reset button now uses different switch with taller height so it is much better to find by feel so you do not have to look around the side of the printer to find it (ie. if your board is mounted on the side). I don't know what firmware changes were done but test prints came out perfect so it seems no compatibility issues should arise. Still haven't done long prints but description says some design faults have been rectified so I hope at least my over-heating/shut-off issue does not reappear. Looks like a good upgrade board if you have one of the earlier Anet A8 clones.

Layout of board much improved. Board, extruder and bed connectors now all of the same type and more sturdily soldered to the board. Reset button now uses different switch with taller height so it is much better to find by feel so you do not have to look around the side of the printer to find it (ie. if your board is mounted on the side). I don't know what firmware changes were done but test prints came out perfect so it seems no compatibility issues should arise. Still haven't done long prints but description says some design faults have been rectified so I hope at least my over-heating/shut-off issue does not reappear. Looks like a good upgrade board if you have one of the earlier Anet A8 clones.

Layout of board much improved. Board, extruder and bed connectors now all of the same type and more sturdily soldered to the board. Reset button now uses different switch with taller height so it is much better to find by feel so you do not have to look around the side of the printer to find it (ie. if your board is mounted on the side). I don't know what firmware changes were done but test prints came out perfect so it seems no compatibility issues should arise. Still haven't done long prints but description says some design faults have been rectified so I hope at least my over-heating/shut-off issue does not reappear. Looks like a good upgrade board if you have one of the earlier Anet A8 clones.

convient a ma demande

convient a ma demande

convient a ma demande

La carte reçu ne correspond pas a la photo ci-contre (A8) reçu A8+ Tromperie sur la marchandise. Envoyer moi un bon de retour pour remboursement.

La carte reçu ne correspond pas a la photo ci-contre (A8) reçu A8+ Tromperie sur la marchandise. Envoyer moi un bon de retour pour remboursement.

La carte reçu ne correspond pas a la photo ci-contre (A8) reçu A8+ Tromperie sur la marchandise. Envoyer moi un bon de retour pour remboursement.

good quality

good quality

good quality