ApoMar
Q: it works on any operating system or just windows?
Preguntado por ApoMar sobre 2024-04-28 05:31:16Q: does it come with driver or it's just plug and play?
Preguntado por ApoMar sobre 2024-04-28 05:28:13
Q: from where i can buy the filaments for this 3d printer ?
Preguntado por ApoMar sobre 2024-03-05 03:28:55Q: from where can we get the original code for it ?
Preguntado por ApoMar sobre 2024-01-05 12:14:22
Hemistich Click More information to open: Github Github Microphone Micropython ESP32 Firmware Download
2024-01-08 03:31:31 Servicial (3)Q: if i buy this set,can i have all labeled,i mean each set ?
Preguntado por BG155562299 sobre 2021-07-28 06:47:00
NickSenzaName Yes, on each set you can see the corresponding value
2022-04-02 03:25:20 Servicial (0)
kixrox no idea
2022-02-10 12:40:01 Servicial (0)
ababa13 it's so peculiar
2022-01-16 01:23:49 Servicial (0)
tommielauriks Usbstandards are wicket bad, it is not just you. Blame Apple mostly but all are guilty. More plugs, more money, it is wild. Anyway, this one is called usb mini, was "the" solution for all phones, until replaced because it was not flat enough.
2022-01-09 08:47:15 Servicial (1)
Q: how do you know when it is empty ? it doesn't look like you can see that...
Preguntado por BG155562299 sobre 2021-07-18 04:54:17
ayman86 جيد
2021-12-26 12:01:03 Servicial (0)Q: from where to buy the mops for it ? a link please
Preguntado por BG155562299 sobre 2021-07-19 12:10:37
mk_glover The board is self explanatory and is designed to be powered from the USB interface. It uses an FTDI FT232RL USB to UART chip with TTL levels on the serial interface. The datasheet for the chip is is available on the FTDI website.:- DS_FT232R.pdf. However, the board and chip does support being powered by a +3.3V to +5.25V supply on the "5V" hole for the device core. This is the Vcc pin of the chip. Now, the hole labelled "VCC" is connected to the VCCIO pin of the FTDI device and in the words of FTDI:- "+1.8V to +5.25V supply to the UART Interface and CBUS group pins (1...3, 5, 6, 9...14, 22, 23). In USB bus powered designs connect this pin to 3V3OUT pin to drive out at +3.3V levels, or connect to VCC to drive out at 5V CMOS level. This pin can also be supplied with an external +1.8V to +2.8V supply in order to drive outputs at lower levels. It should be noted that in this case this supply should originate from the same source as the supply to VCC. This means that in bus powered designs a regulator which is supplied by the +5V on the USB bus should be used." Care may be required for supply isolation in your application.
2021-11-28 09:15:11 Servicial (0)
ApoMar actuallyis very simple,on each side is a HV and an LV,on the HV side goes 5v and on the LV side the 3,3V, H-High,L-Low,tx to tx and rx to rx,on each side
¡Te invitamos sinceramente a suscribirte al correo electrónico de respuesta de invitación!
Si se suscribe, lo invitaremos por correo electrónico para que responda las preguntas que la gente tenga sobre los productos. ¡Al suscribirte, también ganarás la "Insignia útil "! Puede darse de baja en cualquier momento en la página de configuración de privacidad.
¡Ayuda a los demás y sé más feliz!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
