it's light, it looks clean and it takes 2-3S. perfect for ultralight toothpick. BUT these pads are a pain. My solder did not stick well enough, irrespective of the amount of flux I used. Then I overheated the board and the component immediately right to the positive fell off. I've resoldered it and tested the board. All good. Eventually I decided to put the positive cable on the other side of the board. Again the soldering took ages as my solder (a good quality one) would not stick to the pads. Oh if you ask, yes the plug goes 'up'. I'm planning to flip and rotate the FC...

it's light, it looks clean and it takes 2-3S. perfect for ultralight toothpick. BUT these pads are a pain. My solder did not stick well enough, irrespective of the amount of flux I used. Then I overheated the board and the component immediately right to the positive fell off. I've resoldered it and tested the board. All good. Eventually I decided to put the positive cable on the other side of the board. Again the soldering took ages as my solder (a good quality one) would not stick to the pads. Oh if you ask, yes the plug goes 'up'. I'm planning to flip and rotate the FC...

it's light, it looks clean and it takes 2-3S. perfect for ultralight toothpick. BUT these pads are a pain. My solder did not stick well enough, irrespective of the amount of flux I used. Then I overheated the board and the component immediately right to the positive fell off. I've resoldered it and tested the board. All good. Eventually I decided to put the positive cable on the other side of the board. Again the soldering took ages as my solder (a good quality one) would not stick to the pads. Oh if you ask, yes the plug goes 'up'. I'm planning to flip and rotate the FC...

It’s 0.4g heavier than the specs say which isn’t great for my ultralight build, but otherwise I can’t complain. Been using it for a few weeks now on my DJI whoop and no issues.

It’s 0.4g heavier than the specs say which isn’t great for my ultralight build, but otherwise I can’t complain. Been using it for a few weeks now on my DJI whoop and no issues.

It’s 0.4g heavier than the specs say which isn’t great for my ultralight build, but otherwise I can’t complain. Been using it for a few weeks now on my DJI whoop and no issues.

low cost F4 AIO whoop board for my 2S 85mm whoop. Or good for toothpick 2,5inch quad. XT30 is included

low cost F4 AIO whoop board for my 2S 85mm whoop. Or good for toothpick 2,5inch quad. XT30 is included

low cost F4 AIO whoop board for my 2S 85mm whoop. Or good for toothpick 2,5inch quad. XT30 is included

初心者で、使えるか心配していましたが、良好に作動してましたが！間違えてバッテリーの不良でＦCが破損しましたので💦再購入します。 因みにtiny fork IIの機体とモーターを使い良好に飛ばしていました💦

初心者で、使えるか心配していましたが、良好に作動してましたが！間違えてバッテリーの不良でＦCが破損しましたので💦再購入します。 因みにtiny fork IIの機体とモーターを使い良好に飛ばしていました💦

初心者で、使えるか心配していましたが、良好に作動してましたが！間違えてバッテリーの不良でＦCが破損しましたので💦再購入します。 因みにtiny fork IIの機体とモーターを使い良好に飛ばしていました💦

it's ok for 75mm 2s whoop

it's ok for 75mm 2s whoop

it's ok for 75mm 2s whoop

Ho acquistato questa FC da usare come ricambio per il Geelang Anger 85X hd spedizione veloce come sempre

Ho acquistato questa FC da usare come ricambio per il Geelang Anger 85X hd spedizione veloce come sempre

Ho acquistato questa FC da usare come ricambio per il Geelang Anger 85X hd spedizione veloce come sempre

spedizione rapida ho comprato questa fc da usare come ricambio per il Geelang Anger 85X

spedizione rapida ho comprato questa fc da usare come ricambio per il Geelang Anger 85X

spedizione rapida ho comprato questa fc da usare come ricambio per il Geelang Anger 85X

ho acquistato questa FC come ricambio per il drone Geelang 85X HD

ho acquistato questa FC come ricambio per il drone Geelang 85X HD

ho acquistato questa FC come ricambio per il drone Geelang 85X HD

Excellent

Excellent

Excellent

arrived early

arrived early

arrived early