This is a very nice micro servo. Its strength and speed vs weight is unparalleled by any other micro servo I've found. The output shaft is free to turn 360 degrees but the controller will only rotate it about +/- 50 degrees. I was hoping it would achieve +/- 90 to be used on a robot. I connected it to an Arduino and used the writeMicroseconds command to try out of range values and it still only turns +/- 50 degrees. I disassembled one to check the construction quality. All the gears are metal and there are two ball bearings supporting the output shaft. The potentiometer was 1800 ohms with a 2.5V reference voltage and over 180 deg of useable rotation. In theory this digital servo should be programmable to modify the angular limits but I couldn't find any documentation. There are 4 SOT23 transistors on the circuit board that appear to be a full discrete H-Bridge driving the motor. The control horns felt a little loose and the spline would occasionally slip if stalled. The midsection of the housing does appear to be made of some kind of metal. I was able to solvent weld a small piece of ABS to the bottom plate using acetone so the top and bottom plates are likely made of ABS. I really like this servo and would buy many more if there was a way to increase the rotation angle.

This is a very nice micro servo. Its strength and speed vs weight is unparalleled by any other micro servo I've found. The output shaft is free to turn 360 degrees but the controller will only rotate it about +/- 50 degrees. I was hoping it would achieve +/- 90 to be used on a robot. I connected it to an Arduino and used the writeMicroseconds command to try out of range values and it still only turns +/- 50 degrees. I disassembled one to check the construction quality. All the gears are metal and there are two ball bearings supporting the output shaft. The potentiometer was 1800 ohms with a 2.5V reference voltage and over 180 deg of useable rotation. In theory this digital servo should be programmable to modify the angular limits but I couldn't find any documentation. There are 4 SOT23 transistors on the circuit board that appear to be a full discrete H-Bridge driving the motor. The control horns felt a little loose and the spline would occasionally slip if stalled. The midsection of the housing does appear to be made of some kind of metal. I was able to solvent weld a small piece of ABS to the bottom plate using acetone so the top and bottom plates are likely made of ABS. I really like this servo and would buy many more if there was a way to increase the rotation angle.

This is a very nice micro servo. Its strength and speed vs weight is unparalleled by any other micro servo I've found. The output shaft is free to turn 360 degrees but the controller will only rotate it about +/- 50 degrees. I was hoping it would achieve +/- 90 to be used on a robot. I connected it to an Arduino and used the writeMicroseconds command to try out of range values and it still only turns +/- 50 degrees. I disassembled one to check the construction quality. All the gears are metal and there are two ball bearings supporting the output shaft. The potentiometer was 1800 ohms with a 2.5V reference voltage and over 180 deg of useable rotation. In theory this digital servo should be programmable to modify the angular limits but I couldn't find any documentation. There are 4 SOT23 transistors on the circuit board that appear to be a full discrete H-Bridge driving the motor. The control horns felt a little loose and the spline would occasionally slip if stalled. The midsection of the housing does appear to be made of some kind of metal. I was able to solvent weld a small piece of ABS to the bottom plate using acetone so the top and bottom plates are likely made of ABS. I really like this servo and would buy many more if there was a way to increase the rotation angle.

using them as cyclic servo and tail servo for copter x 250 . buy with confindence

using them as cyclic servo and tail servo for copter x 250 . buy with confindence

using them as cyclic servo and tail servo for copter x 250 . buy with confindence

بالنسبة للسعر لا يمكنك الحصول على أي شيء أفضل !!!

For the price you can't get anything better!!!

بالنسبة للسعر لا يمكنك الحصول على أي شيء أفضل !!!

لقد طلبت هذه الأجهزة لطائرتي الرغوة في الهواء الطلق يزن D0576HT 8.2 جرام بدون ذراع servo وبرغي وسط يقاس على مقياس غرام رقمي. إنها مدرجة على أنها 7.9 جرام لكني حاولت أن أزن 2 قطعة وحصلت على 8.2 جرام جهاز الإرسال يأتي مع تشكيلة من الأسلحة و كنت متفاجئة من أن أحدهم كان طويلاً جداً مناسبة لثعابين ثلاثية الأبعاد اعتدت على عمل تمديدات القرن الفينول كما D074 من Inservos لا يأتي مع الذراع سيرفو طويلة. عمل جيد بلو آرو أنا زودتها بالطاقة مع بطارية LiFe 6.6 فولت للتحقق من ما إذا كان يعمل. نتائجي الأولية هي أن D0576HT سريع جداً، أسرع من D0474 ومركز جيداً. مواصفات عزم الدوران مبهرة و لا أطيق الإنتظار لتثبيت هذه الأجهزة في طائرتي الثالثة.

I ordered these servos for my outdoor foamy airplanes. The D0576HT weighs 8.2 g without servo arm and center screw measured on a digital gram scale. It is listed as 7.9g but I tried weighing 2 pcs and got 8.2g. The servo comes with an assortment of servo arms and I was pleasantly surprised that one of them was extra long. Fit for a 3d foamy. I used to have to make phenolic horn extensions as the D074 from Inservos didn't come with the long servo arm. Nice job BlueArrow. I powered it up with a LiFe 6.6V battery to check if it was working. No problems. My initial findings are the D0576HT is very fast, faster than the D0474 and centered well. Torque specs are impressive and I can't wait to install these servos in my 3d plane.

لقد طلبت هذه الأجهزة لطائرتي الرغوة في الهواء الطلق يزن D0576HT 8.2 جرام بدون ذراع servo وبرغي وسط يقاس على مقياس غرام رقمي. إنها مدرجة على أنها 7.9 جرام لكني حاولت أن أزن 2 قطعة وحصلت على 8.2 جرام جهاز الإرسال يأتي مع تشكيلة من الأسلحة و كنت متفاجئة من أن أحدهم كان طويلاً جداً مناسبة لثعابين ثلاثية الأبعاد اعتدت على عمل تمديدات القرن الفينول كما D074 من Inservos لا يأتي مع الذراع سيرفو طويلة. عمل جيد بلو آرو أنا زودتها بالطاقة مع بطارية LiFe 6.6 فولت للتحقق من ما إذا كان يعمل. نتائجي الأولية هي أن D0576HT سريع جداً، أسرع من D0474 ومركز جيداً. مواصفات عزم الدوران مبهرة و لا أطيق الإنتظار لتثبيت هذه الأجهزة في طائرتي الثالثة.

تلك الأجهزة قوية وسريعة جداً قوية جداً مصنوعة بشكل جيد، لديهم بعض الركود بعد فترة، بالكاد ملحوظ، مُقترح

those servos are mighty ,super fast super strong,well made ,they have some slack after a while ,barely noticeable ,suggested

تلك الأجهزة قوية وسريعة جداً قوية جداً مصنوعة بشكل جيد، لديهم بعض الركود بعد فترة، بالكاد ملحوظ، مُقترح

لن أشتري من بانججود مجدداً التسليم طويل جداً جداً لست مستحماً لأختبر إن كان يعمل لأنني اشتريته من متجر آخر بعد أن طلبت هذا وقد جاء قبل ذلك بكثير

i will never buy from banggood again, delivery real super, super long, im not really bather to test if it works because i already bought it from another store way after i order this and it came way before

لن أشتري من بانججود مجدداً التسليم طويل جداً جداً لست مستحماً لأختبر إن كان يعمل لأنني اشتريته من متجر آخر بعد أن طلبت هذا وقد جاء قبل ذلك بكثير

servo ممتاز دقيق جدا، مركز مثالي والكثير من الطاقة

Excellent servo super precise, perfect centering and plenty of power

servo ممتاز دقيق جدا، مركز مثالي والكثير من الطاقة

خدم ممتازون

ottimi servi

خدم ممتازون

gute Qualität guter Preis

gute Qualität guter Preis

gute Qualität guter Preis

Kleine Abmessungen alles bestens und auch für den HV Betrieb.

Kleine Abmessungen alles bestens und auch für den HV Betrieb.

Kleine Abmessungen alles bestens und auch für den HV Betrieb.