Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (480)
  • Imagem (43)
  • Vídeo (2)
  • Todas as estrelas
    • Todas as estrelas(480)
    • Estrela(459)
    • Estrela(14)
    • Estrela(2)
    • Estrela(3)
    • Estrela(2)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (United States)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 10/02/2014

    I bought again and again from here. Perfect quality and shippment. This arduino is a perfect image of original one and it works in the same good parameter and good condition.After 12 hours of work it remaining upstairs without heat cpu or otherelse. Good quality of soldering and pins. NICE WORK. GREATE SELLER!

    Comentários
    Mostrar original
  • 03/04/2014

    This is a very cheap Arduino Due Clone. Unfortunately my board do not work out of the box. After some research i find out, that in the position of C20, an 0 ohm resistor was mounted instead of a 10 nf capacitor, and a second capacitor (C29) was soldered only on one side. The problem is easy detectable: There is a short between MASTER-RESET and 3.3 Volt. You may see the following problems: -- You can download a sketch, but it do not start. You can start the sketch by pressing reset. -- If a sketch is running, you get the message, that no board is responding on the interface. Again, pressing the reset button help. As the reset button short the 3.3 volt supply without the modification, the lifetime of the reset button is very limited. ==> After fixing this problems, the board works like an original Arduino Due board. I think, this is a good product, and i will reorder another one.

    Comentários
    Mostrar original
  • 13/05/2017

    The Good: * Does not use CH340-based serial chipset used by many other Arduino-compatible boards: this means that it's plug-and-play in Windows. * Can act as a USB device just fine; I was worried that USB HID functionality would not work. * Significantly cheaper than the original product (which is about twice the price at the time of purchase). The Mediocre: * Silkscreening on the board is legible. Some cheapie boards have awful print jobs - this is not one of them. The Bad: * Has the same flaw as the mainline Genuino Due R3: sketches fail to start when the board is first plugged in to power, and requires a press of the reset button. This is extremely irritating - a few workarounds are suggested elsewhere online, such as a capacitor on the reset pin to trigger it once upon power up. Don't expect to work robustly if you put this into a sealed enclosure without some extra leg work. * Female header pins are soldered somewhat crooked, so shields are not going to fit great, and the board overall looks a little sloppy. This matches my experience with most of the Arduino-compatible boards I've seen on Banggood. Not a big deal unless you plan to use shields. I'm likely going to purchase more of these if I can figure out how to deal with the reset issue. It's a passable product, and reasonably good value considering what you pay for it.

    Comentários (1)
    Mostrar original
  • 13/11/2014

    Very good clone of the DUE, awesome board. Works great. As others mentioned: - you MUST be careful about the 3.3V vs 5V for most other arduino boards - you also must pay attention to library compatibility. Most of them will not work with the DUE (because of the ARM cpu instead of the "regular" AVR cpus found in most other arduino boards) To make sure, juste put your arduino IDE in "DUE" mode and check if your program build fine!

    Comentários (2)
    Mostrar original
  • 20/03/2016

    A good product fully compatible with all Arduino Due Shields and accessories. Its a very good quality/price ratio product. Warning : the inputs/outputs of the Arduino Due can tolerate only 3.3V , I advise you to buy TTL Bi-directional Logic Level converter from Banggood : http://www.banggood.com/10-Pcs-3_3V-5V-TTL-Bi-directional-Logic-Level-Converter-For-Arduino-p-951181.html

    Comentários
    Mostrar original
  • 10/05/2020

    Funciona bem, mas tem alguns defeitos menores, como escritos esmaecidos (veja as fotos). As soldas na parte de trás são boas e limpas.

    Comentários
    Mostrar original
  • LMPVIP4
    PT
    23/01/2020

    Está bem, está bem

    Comentários
    Mostrar original
  • 28/05/2019

    purchased for programming experiments. not yet tested, only powered with an USB cable for verifying the already loaded program, then loaded with a blink program. very well made. suggested and satisfied. acquistato per esperimenti di programmazione. non ancora testato, alimentato solo con un cavo USB per verificare il programma già caricato e quindi provato con il programma di lampeggio. molto ben fatto. suggerito e soddisfatto.

    Comentários
    Mostrar original
  • 27/09/2018

    as always the Geekcreit boards are manufactured very well and works as expected. Superb Arduino Due clone. I tested it with Linus Mint loading some simple scketches and everything works fine. satisfied and suggested. good value for money come sempre le schede Geekcreit sono prodotte molto bene e funzionano come previsto. Superbo clone di Arduino Due. L'ho provato con Linus Mint caricando alcuni semplici scketches e tutto funziona perfettamente. soddisfatto e suggerito. buon rapporto qualità prezzo

    Comentários
    Mostrar original
  • 24/03/2018

    Very powerful Arduino board. It has plenty of digital and analog inputs and outputs. Two USB, power supply, some built-in switches and LEDs.

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • US$6.99
    • US$4.40
    • US$24.99
    • US$5.40
    • US$18.99
    • US$59.99
    • US$6.99
    • US$31.39
    • US$39.99
    • US$15.99
    • US$6.99
    • US$5.99
    • US$61.41
    • US$33.99
    • US$159.99
    • US$115.99
    • US$74.99
    • US$3.99