Tak niesamowicie malutki, nie mogę się doczekać, aż znajdę nowe projekty, które wykorzystam na... Jeśli planujesz podłączyć i odłączyć płytę, dla rozwoju lub w inny sposób, upewnij się, że wspierasz port micro USB (Osadziłem cały koniec deski czystym epoksydem, pozostawiając tylko podkładki lutujące czyste) Ponieważ są skłonni zerwać z użyciem...

So amazingly tiny, I am looking forward to finding new projects for me to use these on... If you plan to be plugging and unplugging the board, for development or otherwise, be sure to support the micro USB port (I encased the entire end of the board in clear epoxy, leaving just the solder pads clear), as they are prone to break off with use...

Tak niesamowicie malutki, nie mogę się doczekać, aż znajdę nowe projekty, które wykorzystam na... Jeśli planujesz podłączyć i odłączyć płytę, dla rozwoju lub w inny sposób, upewnij się, że wspierasz port micro USB (Osadziłem cały koniec deski czystym epoksydem, pozostawiając tylko podkładki lutujące czyste) Ponieważ są skłonni zerwać z użyciem...

Really good packed i like packing and micro comes with headers packed with plastic pack very nice bangood thanks once more..

Really good packed i like packing and micro comes with headers packed with plastic pack very nice bangood thanks once more..

Really good packed i like packing and micro comes with headers packed with plastic pack very nice bangood thanks once more..

Przybył bardzo szybko, w ciągu 11 dni, w całkowicie prawidłowym stanie fizycznym. Pozostaje do wypróbowania. To jest przedmiot urazu, poprzedni gdzieś utknął.

It arrived very quickly, in just 11 days, in completely correct physical condition. It remains to be tried. This is a resent item, the previous one was stuck somewhere.

Przybył bardzo szybko, w ciągu 11 dni, w całkowicie prawidłowym stanie fizycznym. Pozostaje do wypróbowania. To jest przedmiot urazu, poprzedni gdzieś utknął.

Wszystko w porządku, zapisz pakiet. Mój stary sternik uratował :)

Everytking is ok, save package. My old gaming steringwheel saved :)

Wszystko w porządku, zapisz pakiet. Mój stary sternik uratował :)

I ordered two of these boards and they arrived much faster than I expected and were in good condition. They were individually packed in static bags and came with two header pins as shown on the product page. Soldering them was easy - stick the pins into a breadboard and set the board down so the pins go through the holes. No need for any tools to hold everything in place. Windows 10 recognized the boards and installed the correct drivers automatically; the Arduino application saw them too and I was able to program them immediately. It worked! Note that while this board is compatible with a Leonardo (same MCU), the built-in LED on a Leonardo (on Pin 13) does not exist on this board. I ran into some trouble with one of them that was entirely my own fault. Based on the silkscreen markings on the board and its size, I thought I'd try using the SparkFun Pro Micro drivers. Things worked fine until I programmed the board, after which Windows would no longer recognize it as a usable USB device. Turns out the SparkFun Pro Micro comes in two flavours: 5V/16MHz and 3.3V/8MHz, and the driver defaults to 3.3V/8MHz. The solution to the problem is to change the board type in the Arduino application back to Leonardo (5V), then ground the /RST pin twice, quickly. After that, the bootloader will wait for eight seconds for you to set the Arduino software to the correct COM port and upload your program, making sure you have the board type set to Leonardo. It took me a couple of tries but I brought the board back from the dead. If you ever program your board and it no longer works and your computer can't seem to communicate with it anymore, try the above technique, or do a search for "pro-micro fail troubleshooting" it's where I got the above from. This is a great little board with more pins than you'd expect for a device this small, and it plugs nicely into a breadboard, leaving plenty of room for other components.

I ordered two of these boards and they arrived much faster than I expected and were in good condition. They were individually packed in static bags and came with two header pins as shown on the product page. Soldering them was easy - stick the pins into a breadboard and set the board down so the pins go through the holes. No need for any tools to hold everything in place. Windows 10 recognized the boards and installed the correct drivers automatically; the Arduino application saw them too and I was able to program them immediately. It worked! Note that while this board is compatible with a Leonardo (same MCU), the built-in LED on a Leonardo (on Pin 13) does not exist on this board. I ran into some trouble with one of them that was entirely my own fault. Based on the silkscreen markings on the board and its size, I thought I'd try using the SparkFun Pro Micro drivers. Things worked fine until I programmed the board, after which Windows would no longer recognize it as a usable USB device. Turns out the SparkFun Pro Micro comes in two flavours: 5V/16MHz and 3.3V/8MHz, and the driver defaults to 3.3V/8MHz. The solution to the problem is to change the board type in the Arduino application back to Leonardo (5V), then ground the /RST pin twice, quickly. After that, the bootloader will wait for eight seconds for you to set the Arduino software to the correct COM port and upload your program, making sure you have the board type set to Leonardo. It took me a couple of tries but I brought the board back from the dead. If you ever program your board and it no longer works and your computer can't seem to communicate with it anymore, try the above technique, or do a search for "pro-micro fail troubleshooting" it's where I got the above from. This is a great little board with more pins than you'd expect for a device this small, and it plugs nicely into a breadboard, leaving plenty of room for other components.

I ordered two of these boards and they arrived much faster than I expected and were in good condition. They were individually packed in static bags and came with two header pins as shown on the product page. Soldering them was easy - stick the pins into a breadboard and set the board down so the pins go through the holes. No need for any tools to hold everything in place. Windows 10 recognized the boards and installed the correct drivers automatically; the Arduino application saw them too and I was able to program them immediately. It worked! Note that while this board is compatible with a Leonardo (same MCU), the built-in LED on a Leonardo (on Pin 13) does not exist on this board. I ran into some trouble with one of them that was entirely my own fault. Based on the silkscreen markings on the board and its size, I thought I'd try using the SparkFun Pro Micro drivers. Things worked fine until I programmed the board, after which Windows would no longer recognize it as a usable USB device. Turns out the SparkFun Pro Micro comes in two flavours: 5V/16MHz and 3.3V/8MHz, and the driver defaults to 3.3V/8MHz. The solution to the problem is to change the board type in the Arduino application back to Leonardo (5V), then ground the /RST pin twice, quickly. After that, the bootloader will wait for eight seconds for you to set the Arduino software to the correct COM port and upload your program, making sure you have the board type set to Leonardo. It took me a couple of tries but I brought the board back from the dead. If you ever program your board and it no longer works and your computer can't seem to communicate with it anymore, try the above technique, or do a search for "pro-micro fail troubleshooting" it's where I got the above from. This is a great little board with more pins than you'd expect for a device this small, and it plugs nicely into a breadboard, leaving plenty of room for other components.

Пришло как описано, упаковано нормально. Подключил, установил драйвера из среды разработки - плата нормально определилась и заработала. Припаял туда FrSky передатчик для того чтобы сделать самодельный usb адаптер для вертолётного симулятора. Работает как и задумано. Итоговый результат запаковал в термоусадку для удобства. Паять тоже просто к этой плате. Визуально по качеству платы тоже всё хорошо.

Пришло как описано, упаковано нормально. Подключил, установил драйвера из среды разработки - плата нормально определилась и заработала. Припаял туда FrSky передатчик для того чтобы сделать самодельный usb адаптер для вертолётного симулятора. Работает как и задумано. Итоговый результат запаковал в термоусадку для удобства. Паять тоже просто к этой плате. Визуально по качеству платы тоже всё хорошо.

Пришло как описано, упаковано нормально. Подключил, установил драйвера из среды разработки - плата нормально определилась и заработала. Припаял туда FrSky передатчик для того чтобы сделать самодельный usb адаптер для вертолётного симулятора. Работает как и задумано. Итоговый результат запаковал в термоусадку для удобства. Паять тоже просто к этой плате. Визуально по качеству платы тоже всё хорошо.

El producto en óptimas condiciones

El producto en óptimas condiciones

El producto en óptimas condiciones

Świetny produkt, w ide Arduino trzeba wybrać arduino leonardo, używa usb mini, zawsze lepiej niż nano uchwyt, i jest mniejszy rozmiar w porównaniu, więc zalecane

ottimo prodotto, nell ide di Arduino bisogna selezionare arduino leonardo, utilizza usb mini, sempre meglio della presa del nano, ed è di dimensioni minori in confronto, quindi raccomandato

Świetny produkt, w ide Arduino trzeba wybrać arduino leonardo, używa usb mini, zawsze lepiej niż nano uchwyt, i jest mniejszy rozmiar w porównaniu, więc zalecane

Doskonały produkt, zamówione trzy, były w torbach ESD. Z jednej z nich zrobił makropad

Excellent product. Ordered three, they came in ESD bags. Made a macropad out of one of them :)

Doskonały produkt, zamówione trzy, były w torbach ESD. Z jednej z nich zrobił makropad

Bardzo dobrze

muito bom

Bardzo dobrze