blitzen
mijn inhoud
Alle berichten
Beoordelingen
Reacties
antwoorden
vragen

Alle berichten

blitzen 16/01/2019
This combo board has a 4 channel receiver for a motor, rudder, elevator and aileron. There are 6 outputs. Brushed motor solder pads. Brushless ESC solder pads. 2 servos (rudder and elevator). 2 connectors for the opposing ailerons. The receiver auto binds after 10 seconds. Setup a new model with FrSky D8 on the TX and set to bind. Then power the receiver. Wait for steady light, then power off. No mention current ratings. The speed control was able to handle a 0720 17000KV core-less motor. The largest LiPo battery tested was a 3.7V 250 mAh 35C. Alternately, a 1S brushless motor and a tiny ESC can be used. The onboard linear servos are relatively quick and pull 35g. The control horn, pushrod and servo should extend along a straight line. That way the push rod transfers the most movement (7mm) and results in enough control surface sweep. 2 tiny (1m) onboard JST connectors replaces an aileron wiring harness that wires a pair of micro linear servos to operate oppositely (which rolls the aircraft). Adding a pair of digital servos will cost about $20. There is no telemetry but the plane will drop if the signal is lost. The receiver doesn’t appear to have a low voltage cutoff so setting a timer is a good idea. Initially, the receiver seems a little jittery with nothing connected. After setting up the model, it calmed down considerably. Configuring the receiver is a function of a programmable transmitter. I’ve been using the TaranisQ X7.
Oversky MXL-RX62H V3 RC Vliegtuigontvanger geïntegreerd met Dubbele Servo voor Frsky DSMX DMS2 FUTABA SFHSS
US$32.90 US$46.79
24
aanbevelingen
Reacties (4)
blitzen 04/10/2019
The TeenyF4 Pro Flytower comes with 2M standoffs, screws and nuts. I also used tiny rubber rings (and longer screws) to soft mount the flytower onto a SPC 95EP frame. Soldering the motors to the 4 in 1 ESC was easy. The 5A ESC can handle motors as large as 1102. I'm using smaller Happymodel 0802 19000KV motors (1S). A battery connector is not included with the flytower. I chose a JST-PH2 battery connector and 3.8V 450 mAh LiPos. The solder pads on the flight control board are very small and require a steady hand. A small tipped soldering iron is helpful. I've attached a 25mw AIO Cam/VTX w/ OSD and a small FrSky D8 receiver. After binding the receiver to the TX and configuring basic settings in Betaflight, the quadcopter flew surprisingly well. Updating the firmware and configuring Betaflight (PIDs and rates) is the next step.The green propellers shown in the picture have been discontinued. Red & black Eachine 3 blade propellers are current. All of the parts mentioned here are available from Banggood. I would recommend the TeenyF4 Pro to anyone interested in building a compact lightweight micro.
16x16mm TeenyF4 Pro 1-2S Flytower F4 OSD FC met Buck-Boost Converter & 5A BL_S DShot600 4In1 ESC
US$32.54 US$34.23
0
aanbevelingen
Reacties (0)
0.1g 16x16mm naar 20x20mm vlucht controller verbinding Converter Board voor RC Drone FPV Racing
US$1.99

Q: What size are the holes?

gevraagd door blitzen op 2017-11-30 06:24:23

nonickjustname when will you make 15x15 to 16x16

2018-08-11 08:25:02 Nuttig (0)
Verzenden
antwoorden (1)

blitzen In this case, the transmitter - receiver failsafe isn't there. But the receiver - flight control failsafe should already be set by default. If not, adjust Betaflight failsafe to drop the quad.

krzaq 21/09/2017
used it on furibee f36, works like a charm, flashed with newest betaflight, works ok only thing that you need to know is that it doesn't support failsafe with flysky
Eachine Beecore F3_EVO_Brushed vluchtbesturing voor Inductrix Tiny Whoop Eachine E010 E010S
US$28.99 US$34.99
0
Reacties (1)

Jij bent de expert, kan je helpen?

We nodigen je van harte uit om je te abonneren op de Invite Answer-e-mail!

Als u zich abonneert, nodigen we u uit via e-mail om vragen te beantwoorden die mensen hebben over producten. Door je te abonneren, verdien je ook de "Behulpzame Badge "! U kunt zich op elk moment uitschrijven op de pagina met privacyinstellingen.

Help anderen en wees gelukkiger!

  • Abonneren

Over badges

Badges zijn gerelateerd aan de community en gebruikers verdienen badges door kwaliteitsinhoud te creëren, missies te voltooien of door deel te nemen aan speciale activiteiten. Specifieke mensen hebben ook hun eigen exclusieve badge.
CEO badge

de ceo-badge is alleen in handen van de baas van Banggood.

Badges die je kunt verdienen, komen binnenkort
  • Oké

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • Oké

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe