Recenzje Freewing 1026mm Rozpiętość skrzydeł EPO Delta Wing FPV Flywing RC Samolot KIT - Banggood zakupy online

Freewing 1026mm Rozpiętość skrzydeł EPO Delta Wing FPV Flywing RC Samolot KIT

US$68.99
~~US$82.79~~
Kup Teraz

Opinie klientów

5 z5

Zobacz wszystkie recenzje w12

5 gwiazda
12 (100.0%)
4 gwiazda
0 (0%)
3 gwiazda
0 (0%)
2 gwiazda
0 (0%)
1 gwiazda
0 (0%)

Napisać recenzję Uzyskaj podwójne oceny, jeśli jesteś jedną z pierwszych 3 opublikowanych recenzji!

Wszystkie recenzje(12)
Obrazy
Wideo(2)
Wszystkie gwiazdy
- Wszystkie gwiazdy(12)
- 5 Gwiazda(12)
- 4 Gwiazda(0)
- 3 Gwiazda(0)
- 2 Gwiazda(0)
- 1 Gwiazda(0)

Sortuj według:

Do podglądu

Do podglądu
Najbardziej pomocny
Najnowszy

Recenzje tylko z Twojego kraju (United States)

|

Pokaż oryginał

Część recenzji została przetłumaczona automatycznie.

RagTheNutsOffVIP5
GB
14/05/2018

Upon opening the box, I knew exactly what I was going to it. Glued up in a few minutes and I also laminated mine. Set up with a BR2212 1000Kv motor with a 7x5 prop, then a flight stabilizer (was inav, now a vector), added FPV gear and made a 4S li-on battery pack. Flies very well, although not tested at any speed! One negative point is that this model is quite low density EPO foam. Would have loved to see it in EPP. Oh and there were no magnets in the box to hold the lid down, so used a servo control horn as shown in the photos. And the BG pictures show landing gear, again not in the box.

Upon opening the box, I knew exactly what I was going to it. Glued up in a few minutes and I also laminated mine. Set up with a BR2212 1000Kv motor with a 7x5 prop, then a flight stabilizer (was inav, now a vector), added FPV gear and made a 4S li-on battery pack. Flies very well, although not tested at any speed! One negative point is that this model is quite low density EPO foam. Would have loved to see it in EPP. Oh and there were no magnets in the box to hold the lid down, so used a servo control horn as shown in the photos. And the BG pictures show landing gear, again not in the box.

Upon opening the box, I knew exactly what I was going to it. Glued up in a few minutes and I also laminated mine. Set up with a BR2212 1000Kv motor with a 7x5 prop, then a flight stabilizer (was inav, now a vector), added FPV gear and made a 4S li-on battery pack. Flies very well, although not tested at any speed! One negative point is that this model is quite low density EPO foam. Would have loved to see it in EPP. Oh and there were no magnets in the box to hold the lid down, so used a servo control horn as shown in the photos. And the BG pictures show landing gear, again not in the box.
20

Komentarze (1)

Pokaż oryginał
Rastas97VIP4
FR
04/05/2018

contenu assez complet mais il manque des protections sur le carton d'emballage quelques morceaux abîmée

contenu assez complet mais il manque des protections sur le carton d'emballage quelques morceaux abîmée

contenu assez complet mais il manque des protections sur le carton d'emballage quelques morceaux abîmée
3

Komentarze

Pokaż oryginał

Show:

Całkowity 0 stron

Idź do strony

Iść

Możesz być zainteresowany

recommendation for you