ESP32-CAM-MB Download Onderbord voor ESP32-CAM OV2640 Camera Module Downloader met Micro USB Interface Beoordelingen - Banggood Online winkelen

ESP32-CAM-MB Download Onderbord voor ESP32-CAM OV2640 Camera Module Downloader met Micro USB Interface

US$7.49

Nu kopen

Klantbeoordelingen

3.75 van5

Bekijk alle beoordelingen van4

5 ster
2 (50.0%)
4 ster
1 (25.0%)
3 ster
0 (0%)
2 ster
0 (0%)
1 ster
1 (25.0%)

Schrijf een beoordeling Ontvang dubbele banggoodpunten als je één van de 3 eerste beoordelingen plaatst!

Alle beoordelingen(4)
Afbeeldingen
Videos
Ster
- Ster(4)
- 5 Ster(2)
- 4 Ster(1)
- 3 Ster(0)
- 2 Ster(0)
- 1 Ster(1)

Sorteren op:

Top recensie

Top recensie
Meest nuttig
meest recent

Recensies alleen uit uw land (United States)

|

Toon origineel

Een deel van de recensie is automatisch vertaald.

SquizVIP3
AU
06/01/2024

Order received in good order and on the predicted date.

Order received in good order and on the predicted date.

Order received in good order and on the predicted date.
0

Reacties

Toon origineel
tengucuVIP2
AU
31/05/2023

Very pleased with the boards.

Very pleased with the boards.

Very pleased with the boards.
0

Reacties

Toon origineel
kezbarooVIP4
AU
02/10/2023

Works with windows and not so much with linux. Reset does not work with my particular cam boards, so I use the reset on the cam board

Works with windows and not so much with linux. Reset does not work with my particular cam boards, so I use the reset on the cam board

Works with windows and not so much with linux. Reset does not work with my particular cam boards, so I use the reset on the cam board
0

Reacties

Toon origineel
RoberthVIP4
ZA
19/03/2024

When I tried to use this, it didn't work. It appears the Reset pin doesn't work at all. If I monitor the Comm port when connecting the ESP32 CAM, I have once seen the normal boot up procedure. But pushing the reset didn't put it through a reset - I didn't see anything on the Comm Port. When trying to upload a sketch, Arduino was unable to communicate. Holding down the IO0 button while booting didn't put it in program mode. Holding down the IO0 button and clicking the reset button didn't do anything. Possibly a faulty unit.

When I tried to use this, it didn't work. It appears the Reset pin doesn't work at all. If I monitor the Comm port when connecting the ESP32 CAM, I have once seen the normal boot up procedure. But pushing the reset didn't put it through a reset - I didn't see anything on the Comm Port. When trying to upload a sketch, Arduino was unable to communicate. Holding down the IO0 button while booting didn't put it in program mode. Holding down the IO0 button and clicking the reset button didn't do anything. Possibly a faulty unit.

When I tried to use this, it didn't work. It appears the Reset pin doesn't work at all. If I monitor the Comm port when connecting the ESP32 CAM, I have once seen the normal boot up procedure. But pushing the reset didn't put it through a reset - I didn't see anything on the Comm Port. When trying to upload a sketch, Arduino was unable to communicate. Holding down the IO0 button while booting didn't put it in program mode. Holding down the IO0 button and clicking the reset button didn't do anything. Possibly a faulty unit.
0

Reacties (1)

Toon origineel

Show:

Totaal 0 Pagina's

Ga naar pagina

Gaan

Wellicht ben je ook geïnteresseerd in

recommendation for you