All Messages

Q: Will this work with a 4mm glass bed?

Asked by Meldrac on 2018-04-03 03:11:52

FrankiiSeaStar I tried with creakily glass bed and it did not work . Extruders keeps pushing into the bed when I try to check levels etc . Is there one for glass or does it just need a non seethrough coating on the glass .

2021-02-02 07:43:30 Helpful (0)
Submit
Answers (5)

FrankiiSeaStar You have to add each color you want to cart separately and then you can check them out all together. A one of each color button would be handy for some things 😄

2021-01-29 06:20:41 Helpful (0)
Submit
Answers (1)

FrankiiSeaStar Maybe the color shade depends on ambient climate temperature and changes slightly with different regions . Maybe even soil ph etc can vary the shade

2021-01-28 12:43:25 Helpful (0)
Submit
Answers (1)

FrankiiSeaStar Did u do it .try check in betaflight program in Vtx section to change settings . Can you physically remove the vtx from the stack .

2021-01-28 12:40:13 Helpful (0)
Submit
Answers (1)

FrankiiSeaStar Flying Modes The right switch on the radio controls the different flight modes of easypilot. There are 3 modes: easy, intermediate, and advance. The switch in its first position downward is easy mode, second position is intermediate, and third position is advanced. read the manual

Clermond 04/12/2020
2
Comments (2)

Q: Is it posible to use the remote controler on a simulator?

Asked by BG162274981 on 2021-01-06 06:35:21

FrankiiSeaStar Maybe you can try the wireless USB stick pc adapter which you bind with the transmitter which is FHSS protocol for simulator like the USB adapter for simulators Taranis has but it’s wireless . Make sure it works with the GR8 FHSS PTOTOCOL. The gr8 does not have any USB ports or interface pc ports but it has a binding button which maybe you could bind with the wireless usb simulator adapter. Not 100 percent sure it will work but if you really want it you can research more or just try it .

2021-01-25 11:08:42 Helpful (1)
Submit
Answers (2)

Q: Can you use this controller on a simulator?

Asked by BG143244005 on 2021-01-06 04:04:40

FrankiiSeaStar GEPRC GR8 2.4GHz 8CH FHSS In-built Dual Antenna Remote Controller with GEPRC GR8 8CH Receiver for FPV Racing Freestyle Drones This remote control is only suitable for drones equipped with GEPRC GR8 receiver!!!! NOTE !!! GEPRC GR8 receiver is only suitable for GEPRC GR8 remote control! GEPRC GR8 remote control is only suitable GEPRC GR8 receiver! Players who purchase for the first time must remember to purchase GEPRC GR8 receiver + GEPRC GR8 remote control at the same time. Introduction The remote control has a two-way 2.4G communication protocol with low latency and fast response speed, up to 7 milliseconds. When the receiver receives a low signal, the remote control will send out a vibration alarm. The receiver has the advantages of small size, high sensitivity, long receiver distance, and S-BUS serial port output. With three groups of model memories, you can control three groups of models without re-coding. Vibration motor: When the motor does not vibrate, it means that the remote control sends data stably. When the motor vibrates, it means that the remote control signal is weak and the aircraft should not continue to fly forward. The remote control battery enters a low voltage alarm when the battery is lower than 4.9V. The low voltage alarm is manifested by the buzzer and LED flashing and ringing at a frequency of 1 Hz. GEPRC GR8 Remote control product parameters --Number of channels: 8 --Support model: multi-rotor-traversing aircraft --Wireless frequency: 2.4GHz --T

2021-01-25 10:57:41 Helpful (2)
Submit
Answers (1)

FrankiiSeaStar There is no USB port or interface port so my guess is no and it only can use GR8 receiver

2021-01-25 10:52:54 Helpful (1)
Submit
Answers (2)