Andy0679
Gosomer the prop shaft on the tyro is way to thick to find props that will fit.
2020-07-20 01:31:48 Helpful (2)Q: can I connect a gps module?
Asked by Andy0679 on 2020-11-03 04:17:01
_Red You could, but it wouldn't do much of anything. What you need is a proper F4 flight controller but at that point there is no need for a gyro stabilizer.
2024-09-07 06:24:02 Helpful (0)Q: what is the capacity (mah) of the lipo?
Asked by Andy0679 on 2021-03-28 11:15:53
Scarpa123 50mah
2023-12-21 07:48:41 Helpful (0)
Q: what size is the prop hub shaft? 5mm? 6mm?
Asked by Andy0679 on 2021-08-08 05:43:55
lacvo Kit comes with no electronics, so you supply your own motor. PNP comes with 5mm shaft motor
2022-02-25 08:59:42 Helpful (3)Q: how many mah is the battery?
Asked by Andy0679 on 2022-08-26 07:03:49
Horst 2000mAh
2023-03-31 05:02:30 Helpful (0)Q: Does it flash in rhythm with music?
Asked by Andy0679 on 2022-12-07 12:11:14
wikiloja não recebi, comprei e não recebi
2023-02-27 08:30:10 Helpful (0)
Andy0679 none. you can buy only one or the other JP4IN1 or elrs and purchase the other tx as an external mini tx and mount it to the back.
2022-11-25 01:26:54 Helpful (2)Q: I could only identify 8 physical channels, how is this a 16 channel radio?
Asked by Andy0679 on 2022-08-18 07:51:13
Whinyard it depends on your receiver, it should support 16ch.
2022-08-30 10:23:55 Helpful (1)Q: can I use tbs crossfire with this FC?
Asked by Andy0679 on 2020-10-13 06:55:58
4$how I installed ELRS which uses the same connections for crossfire . Uses tx and rx 1 then set your receiver to crossfire in betaflight
2022-05-15 03:13:42 Helpful (1)Q: what's that mount the GPS module is sitting on? Where can I see it alone?
Asked by Andy0679 on 2022-10-26 11:01:35Q: what's the refresh rate of these servos? What do they opperate at? How many hz?
Asked by Andy0679 on 2022-10-12 09:43:42
Biognosy 1000-2000us, 4.8-7.4v, 333hz
2022-10-13 03:11:52 Helpful (1)Q: Is this iron strong enough for soldering 21700 cells? Or should I go for a spot welder?
Asked by BG211432251 on 2022-09-14 03:33:00
Andy0679 ideally you spot welder batteries but yes this iron will work fine. it'll be a normal solder of course so be very careful not to short the battery. Also you must be very fast at soldering because too much heat will damage the battery and can create an accident.
2022-09-14 04:18:29 Helpful (0)
Q: where do I get the board that I need for inside the case that my receiver plugs into?
Asked by Andy0679 on 2022-08-12 02:44:53
Obnubilate https://www.banggood.com/URUAV-5_8G-RX-PORT-3_0-PLUS-DJI-Digital-or-DJI-V2-FPV-Goggles-Low-Voltage-Alarm-Simulation-Receiver-Board+Metal-Adapter-Mounting-Combo-for-DJI-Fatshark-FPV-Goggles-p-1707616.html?cur_warehouse=CZ&ID=6291331&rmmds=search
2022-08-12 03:22:08 Helpful (1)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
guglielmon G_H_20
2024-12-05 10:01:07 Helpful (0)