Richard
Q: what kind of aileron Servo connector does it have?
Asked by BG382454333 on 2021-04-02 06:23:15
Q: Is part B the Hook or is part C the hook? Which part is Hook and which part is Loop?
Asked by Donald on 2022-06-16 05:30:04
Richard B is loop C is hook When you add to cart and select B or C , the picture changes and the word hook and loop is shown as appropriate.
2022-09-12 07:02:36 Helpful (0)Q: What is the wattage of the amplifier? can be connected to car speakers?
Asked by BG451823504 on 2021-07-19 07:13:25
Richard It only has signal level output. It can be connected to an amplifier which can be connected to car speakers.
2022-08-23 12:06:34 Helpful (0)
Q: Cannot bind to my JR DSM-2 transmitter. Suggestions?
Asked by BG133716492 on 2020-10-06 12:35:42
Richard The required protocol is V761, not DSM. V761 is available in 4in1 multiprotocol modules, as found in many but not all OpenTX transmitters. An example is the Jumper T12 Pro.
2022-01-14 07:21:59 Helpful (0)Q: Hi guys ! Is it possible to bind it why a 2.4Ghz transmitter ? Thanks
Asked by BG184844324 on 2020-05-04 01:32:24
Richard It will bind to OpenTX transmitters like the Jumper T12 Pro. Suitable transmitters must have a 4in1 multiprotocol module. A single multiprotocol module is not sufficient because the V761 protocol is not supported by the chip used in single chip multiprotocol modules.
2022-01-14 07:18:12 Helpful (0)Q: What is the onboard 1s brushed motor speed controller rating, 1,2,3,4,5 amps?
Asked by Anon Youse on 2022-01-13 08:17:11
Richard The V761-1 model uses a 160mAh battery and flies for about 10 minutes. So the battery capacity is one sixth of an Amp-hour and the flight time is one sixth of an hour. This reflects an average current of 1 Amp.
2022-01-14 07:14:32 Helpful (0)
Richard It will bind with OpenTX transmitters that have a 4 in 1 multiprotocol module. It is not sufficient to have a single multiprotocol module.
2022-01-14 07:09:23 Helpful (0)
Q: one glass full of tap water,and the other full of R/O water...Please explain what it means R/O water
Asked by kitsos on 2021-09-04 02:29:18
Richard RO = Reverse Osmosis. Very very pure water.
2021-12-11 11:55:14 Helpful (0)
Q: Can be bind with Jumper T12 ?
Asked by popad on 2021-02-06 10:41:17
Richard I bind them to a Jumper T12 Pro transmitter, which has an inbuilt 4-in1 Multi-protocol module. With a T12 (not Pro) I think you have to put a 4-in-1 module into the bay on the back of the TX.
2021-10-15 08:35:24 Helpful (0)Q: will this be sold as mode 1 as a lot of modlers in australia use mode 1
Asked by unleaded on 2021-04-04 08:34:34
Richard I use them with a Mode 1 Jumper T12 Pro transmitter. That's how I got around there not being mode 1 versions of the OEM transmitters.
2021-10-15 08:30:57 Helpful (0)
Richard@BOOGIE V761protocol for Volantex and Eachine. Then 4 channel sub-option. For gyro control configure 3 position switch on CH5 with settings of -100%, 0% and 100%
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Richard JST 1.25mm pitch
2023-06-10 01:25:00 Helpful (0)