Freewing 1026 mm-es szárnyazású EPO Delta Wing FPV Flywing RC Repülőgép KIT vélemények - Banggood online vásárlás

Freewing 1026 mm-es szárnyazású EPO Delta Wing FPV Flywing RC Repülőgép KIT

US$68.99
~~US$82.79~~
Vásárolj most

Vásárlói vélemények

5 / 5

Az összes 12 vélemény megtekintése

5 csillag
12 (100.0%)
4 csillag
0 (0%)
3 csillag
0 (0%)
2 csillag
0 (0%)
1 csillag
0 (0%)

Írja meg a véleményét Szerezzen dupla értékelési pontot, ha Ön az első 3 közzétett értékelés egyike!

Minden vélemény (12)
Kép (5)
Videó (2)
Minden csillag
- Minden csillag(12)
- 5 Csillag(12)
- 4 Csillag(0)
- 3 Csillag(0)
- 2 Csillag(0)
- 1 Csillag(0)

Sorrend:

Legjobb áttekintés

Legjobb áttekintés
Leghasznosabb
Legfrissebb

Csak az Ön országából származó vélemények (United States)

|

Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

RagTheNutsOffVIP5
GB
14/05/2018

Upon opening the box, I knew exactly what I was going to it. Glued up in a few minutes and I also laminated mine. Set up with a BR2212 1000Kv motor with a 7x5 prop, then a flight stabilizer (was inav, now a vector), added FPV gear and made a 4S li-on battery pack. Flies very well, although not tested at any speed! One negative point is that this model is quite low density EPO foam. Would have loved to see it in EPP. Oh and there were no magnets in the box to hold the lid down, so used a servo control horn as shown in the photos. And the BG pictures show landing gear, again not in the box.

Upon opening the box, I knew exactly what I was going to it. Glued up in a few minutes and I also laminated mine. Set up with a BR2212 1000Kv motor with a 7x5 prop, then a flight stabilizer (was inav, now a vector), added FPV gear and made a 4S li-on battery pack. Flies very well, although not tested at any speed! One negative point is that this model is quite low density EPO foam. Would have loved to see it in EPP. Oh and there were no magnets in the box to hold the lid down, so used a servo control horn as shown in the photos. And the BG pictures show landing gear, again not in the box.

Upon opening the box, I knew exactly what I was going to it. Glued up in a few minutes and I also laminated mine. Set up with a BR2212 1000Kv motor with a 7x5 prop, then a flight stabilizer (was inav, now a vector), added FPV gear and made a 4S li-on battery pack. Flies very well, although not tested at any speed! One negative point is that this model is quite low density EPO foam. Would have loved to see it in EPP. Oh and there were no magnets in the box to hold the lid down, so used a servo control horn as shown in the photos. And the BG pictures show landing gear, again not in the box.
20

Hozzászólások (1)

Mutasd az eredetit
Rastas97VIP4
FR
04/05/2018

contenu assez complet mais il manque des protections sur le carton d'emballage quelques morceaux abîmée

contenu assez complet mais il manque des protections sur le carton d'emballage quelques morceaux abîmée

contenu assez complet mais il manque des protections sur le carton d'emballage quelques morceaux abîmée
3

Hozzászólások

Mutasd az eredetit

Show:

Teljes 0 oldalakat

Menj az oldalra

Megy

Lehet, hogy érdekli

recommendation for you