KorBare
KorBare A 80Volt 300VA centre tapped Toroidal, wired to a 35 amp or more bridge rectifier, followed by a bank of 6 capacitors 47000uf, 3 Capacitors for each Rail, This configuration should produce 58 0 -58 power supply Unloaded and 55 0 -55 fully loaded power supply fully driven to produce the 2X 500Wrms, Yerp that be 1Kwrms
Spidery sorry not sure for that.
2020-08-03 03:55:04 Servicial (0)
Q: Do you sell a power supply that would be perfect for this amp? What is its number?
Preguntado por littlemike sobre 2020-01-21 11:46:27
KorBare Buy an unpopulated Power supply filter board, and populate it with four 10000Uf 100Volt Capacitors "make sure you populate them the right way round" and if the PCB has a place for a Bridge Rectifier install it with a 25 to 35 amp Bridge rectifier and a 35 Amp is best as it's less prone to fail, If the PCB does not have a place for a bridge rectifier on the PCB, Get a square shaped chassis Mount Bridge rectifier and bolt it down to the Chassis. Finally get a 110V centre tapped 300~500VA Toroidal Transformer
2020-07-09 05:02:08 Servicial (0)Q: Can I use it with SMPS? IF yes, then what minimum volts and amperes needed ?
Preguntado por gurnamsingh86 sobre 2019-10-03 02:19:54
KorBare Isuggest you stick with a minimum volts of.. 55 0 -55 Volts and a minimum of 5 Amps Per Module..
2020-07-09 04:28:19 Servicial (0)
KorBare If running a single unit "Mono" a 2 X 45 Volt 500VA Toroidal should be fine, if you are using 2 units "stereo" I would use a dual 55Volt 500VA Toroidal Transformer, don't forget to rectify and filter or smooth out the 58~65Volts DC
2020-06-29 04:51:44 Servicial (1)
KorBare I have two of these and I am using a 240 volt primary step down to 40-0-40 secondary 300VA Toroidal Transformer feeding two bridge rectifiers "One per channel" where each rail is smoothed with a 15000Uf capacitor per rail "a Total of 4 Capacitors", I am using a 10 amp fuse for the mains. BUT Just bare in mind I am only driving 8 Ohm loads where each channel can output 384 clean watts per channel..
2020-06-29 04:44:56 Servicial (1)Q: disponen de la fuente de alimentación necesaria para su funcionamiento?
Preguntado por cesar.eduardo.0 sobre 2018-11-04 06:19:28
KorBare No..You need at least a 80Volt centre tapped 40-0-40 Volt 300VA Toroidal Transformer followed by a bridge rectifier, and at least 2 15000Uf smoothing Capacitors 1 for each 55~65Volt Rail if running two modules "Stereo" with 4 Ohm Loads I would get a 50-0-50 500VA Toroidal
2020-06-29 04:31:29 Servicial (0)¡Te invitamos sinceramente a suscribirte al correo electrónico de respuesta de invitación!
Si se suscribe, lo invitaremos por correo electrónico para que responda las preguntas que la gente tenga sobre los productos. ¡Al suscribirte, también ganarás la "Insignia útil "! Puede darse de baja en cualquier momento en la página de configuración de privacidad.
¡Ayuda a los demás y sé más feliz!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
