Maverick Phantom XT にインストールするのは非常に簡単です。 このRCカーはブラシモーター15Tで、このキットで2Sリポは非常に速く、バッテリー寿命が長い。 車は今、完全に異なっており、運転に非常に積極的です。 工場出荷時の設定は非常に良いので、ESC の設定は不要です。 このキットにBanggoodさん、本当に満足しています。

Very easy to innstall onmy Maverick Phantom XT. This RC car cheaper was in brush motor 15T. Now with this kit with 2S Lipo is very fast and the battery have long time life. The car now is completely different and very aggressive to drive. Is not necessary setup the ESC because factory settings are very good. Thanks Banggood for this kit I am very satisfied.

Maverick Phantom XT にインストールするのは非常に簡単です。 このRCカーはブラシモーター15Tで、このキットで2Sリポは非常に速く、バッテリー寿命が長い。 車は今、完全に異なっており、運転に非常に積極的です。 工場出荷時の設定は非常に良いので、ESC の設定は不要です。 このキットにBanggoodさん、本当に満足しています。

I'm glad I got this! It's a very efficient system and I'm able to run it on nimh's pleasantly, too, if I want. The motor is very smooth and it's connectors fit the esc properly. The esc works well and responds to the program card's settings...mostly. The low brake setting has "less" braking power, but it seems to just be ON, it doesn't ramp up smoothly; and is only useful when you've got fairly good traction. What's amazing is that I can run my truck around slowly if I want and there's almost no cogging - it's almost as smooth as a sensored system - I was amazed. The lvc (low voltage cutoff) works, but be aware that it's a total voltage value per pack setting even though you specify the volts per cell. So, if you have a marginal pack with a low cell, that cell might get really low before the cuttoff kicks in. I use an 8s alarm dongle plugged into the pack because it responds to individual cells. The instruction sheet is just ok and there's no mention of manual calibration. The unit mostly seems to calibrate itself when you attach the battery and turn it on. Although it finds neutral every time, I feel like it pads the trigger pull at full-on. But it's still very controllable and I'll probably get more. If you want a good play system that you could "race" with in a pinch, this qualifies :) I got the 2050kv (17.5 equivalent) and it's good on nimh's and 2s, but really shines on 3s. Be sure to get the little silver program card, it's useful and I didn't even test the esc to see if it's settings can be blipped with a button, but I think not. Also, the temps of the system were normal and what I expected.

I'm glad I got this! It's a very efficient system and I'm able to run it on nimh's pleasantly, too, if I want. The motor is very smooth and it's connectors fit the esc properly. The esc works well and responds to the program card's settings...mostly. The low brake setting has "less" braking power, but it seems to just be ON, it doesn't ramp up smoothly; and is only useful when you've got fairly good traction. What's amazing is that I can run my truck around slowly if I want and there's almost no cogging - it's almost as smooth as a sensored system - I was amazed. The lvc (low voltage cutoff) works, but be aware that it's a total voltage value per pack setting even though you specify the volts per cell. So, if you have a marginal pack with a low cell, that cell might get really low before the cuttoff kicks in. I use an 8s alarm dongle plugged into the pack because it responds to individual cells. The instruction sheet is just ok and there's no mention of manual calibration. The unit mostly seems to calibrate itself when you attach the battery and turn it on. Although it finds neutral every time, I feel like it pads the trigger pull at full-on. But it's still very controllable and I'll probably get more. If you want a good play system that you could "race" with in a pinch, this qualifies :) I got the 2050kv (17.5 equivalent) and it's good on nimh's and 2s, but really shines on 3s. Be sure to get the little silver program card, it's useful and I didn't even test the esc to see if it's settings can be blipped with a button, but I think not. Also, the temps of the system were normal and what I expected.

I'm glad I got this! It's a very efficient system and I'm able to run it on nimh's pleasantly, too, if I want. The motor is very smooth and it's connectors fit the esc properly. The esc works well and responds to the program card's settings...mostly. The low brake setting has "less" braking power, but it seems to just be ON, it doesn't ramp up smoothly; and is only useful when you've got fairly good traction. What's amazing is that I can run my truck around slowly if I want and there's almost no cogging - it's almost as smooth as a sensored system - I was amazed. The lvc (low voltage cutoff) works, but be aware that it's a total voltage value per pack setting even though you specify the volts per cell. So, if you have a marginal pack with a low cell, that cell might get really low before the cuttoff kicks in. I use an 8s alarm dongle plugged into the pack because it responds to individual cells. The instruction sheet is just ok and there's no mention of manual calibration. The unit mostly seems to calibrate itself when you attach the battery and turn it on. Although it finds neutral every time, I feel like it pads the trigger pull at full-on. But it's still very controllable and I'll probably get more. If you want a good play system that you could "race" with in a pinch, this qualifies :) I got the 2050kv (17.5 equivalent) and it's good on nimh's and 2s, but really shines on 3s. Be sure to get the little silver program card, it's useful and I didn't even test the esc to see if it's settings can be blipped with a button, but I think not. Also, the temps of the system were normal and what I expected.

Good motor, still going strong 6 months later, but ESC burned up within the first few weeks. I got this one to replace it and it's much much better: https://www.banggood.com/Racerstar-60A-ESC-Brushless-Waterproof-Sensorless-With-Fan-110-RC-Car-Part-p-1116663.html?p=LN24205151027201606U I highly recommend buying the motor and ESC separately. Here's the motors: https://www.banggood.com/Racerstar-3650-Motor-Brushless-Waterproof-Sensorless-110-RC-Car-Part-5900430039002300KV-p-1110570.html?p=LN24205151027201606U Also don't forget the programming card. The default ESC setup isn't the best. The brakes are set too strong: https://www.banggood.com/Racerstar-LED-Program-Card-For-25354560A-ESC-Motor-Set-p-1057127.html?p=LN24205151027201606U

Good motor, still going strong 6 months later, but ESC burned up within the first few weeks. I got this one to replace it and it's much much better: https://www.banggood.com/Racerstar-60A-ESC-Brushless-Waterproof-Sensorless-With-Fan-110-RC-Car-Part-p-1116663.html?p=LN24205151027201606U I highly recommend buying the motor and ESC separately. Here's the motors: https://www.banggood.com/Racerstar-3650-Motor-Brushless-Waterproof-Sensorless-110-RC-Car-Part-5900430039002300KV-p-1110570.html?p=LN24205151027201606U Also don't forget the programming card. The default ESC setup isn't the best. The brakes are set too strong: https://www.banggood.com/Racerstar-LED-Program-Card-For-25354560A-ESC-Motor-Set-p-1057127.html?p=LN24205151027201606U

Good motor, still going strong 6 months later, but ESC burned up within the first few weeks. I got this one to replace it and it's much much better: https://www.banggood.com/Racerstar-60A-ESC-Brushless-Waterproof-Sensorless-With-Fan-110-RC-Car-Part-p-1116663.html?p=LN24205151027201606U I highly recommend buying the motor and ESC separately. Here's the motors: https://www.banggood.com/Racerstar-3650-Motor-Brushless-Waterproof-Sensorless-110-RC-Car-Part-5900430039002300KV-p-1110570.html?p=LN24205151027201606U Also don't forget the programming card. The default ESC setup isn't the best. The brakes are set too strong: https://www.banggood.com/Racerstar-LED-Program-Card-For-25354560A-ESC-Motor-Set-p-1057127.html?p=LN24205151027201606U

アメリカからAUへの配送は遅い。 モーター(3100kv)とESCは素晴らしい品質です。 協商サンドマスターに26tの金属ピニオンを取り付けた。 ESC を小さなエリアに取り込むために、公正な作業です。 バギーは今、完全に引き裂かれ、ターマックのホイール、GPSは3Sで時速52kmで計時され、フルスロットルでもありませんでした。 ちょっと騒がしいが、バギーの丸いスパーギヤが少し外れているのを責めている。

Delivery was slowish from USA to AU. Motor (3100kv) and ESC look great quality. Installed into Kyosho Sandmaster with a 26t metal pinion. fair bit of work to get ESC into small area. The buggy absolutely rips now, wheelies on tarmac, GPS clocked @ 52km/h with 3S and not even full throttle. Bit noisy but I'm blaming the slightly out of round spur gear on the buggy.

アメリカからAUへの配送は遅い。 モーター(3100kv)とESCは素晴らしい品質です。 協商サンドマスターに26tの金属ピニオンを取り付けた。 ESC を小さなエリアに取り込むために、公正な作業です。 バギーは今、完全に引き裂かれ、ターマックのホイール、GPSは3Sで時速52kmで計時され、フルスロットルでもありませんでした。 ちょっと騒がしいが、バギーの丸いスパーギヤが少し外れているのを責めている。

144001と聖なるシートを 入れて

put in my 144001 and holy sheeet

144001と聖なるシートを 入れて

Honestly I was kind of expect it to be just OK but this is beyond all my expectations. The motor is smooth throughout the range with absolutely no cogging. It has a flat area for pinion screw which isn't shown in the official photo but you can see it in my photo. ESC is sort of OK. I experience some power delay at the top end but not too severe. When I pull the full throttle it stutter a bit before going full power. Apart from that I don't find any fault. ESC temperature is good, motor temperature is good. It's as simple as plug and play but for full adjustability I suggest you to have the programming card too.

Honestly I was kind of expect it to be just OK but this is beyond all my expectations. The motor is smooth throughout the range with absolutely no cogging. It has a flat area for pinion screw which isn't shown in the official photo but you can see it in my photo. ESC is sort of OK. I experience some power delay at the top end but not too severe. When I pull the full throttle it stutter a bit before going full power. Apart from that I don't find any fault. ESC temperature is good, motor temperature is good. It's as simple as plug and play but for full adjustability I suggest you to have the programming card too.

Honestly I was kind of expect it to be just OK but this is beyond all my expectations. The motor is smooth throughout the range with absolutely no cogging. It has a flat area for pinion screw which isn't shown in the official photo but you can see it in my photo. ESC is sort of OK. I experience some power delay at the top end but not too severe. When I pull the full throttle it stutter a bit before going full power. Apart from that I don't find any fault. ESC temperature is good, motor temperature is good. It's as simple as plug and play but for full adjustability I suggest you to have the programming card too.

Wltoys144001のアップグレードには、非常に良い品質のコンボesc 60Aとモーターブラシレス3650 3900kV。 CZストアからの高速配送。

very good quality combo esc 60A and motor brushless 3650 3900kV for my Wltoys144001 upgrade. fast shipping from CZ store.

Wltoys144001のアップグレードには、非常に良い品質のコンボesc 60Aとモーターブラシレス3650 3900kV。 CZストアからの高速配送。

Works well out of the box with factory settings. I disassembled the Esc to inspect it and found that there is no way this esc is waterproof, it works well and is assembled well but there is no protection on the sensitive electronics in the case. To get proper water resistance you will need to take the esc heatsink and case off and coat everything in liquid electrical tape (except for the mosfets touching the heatsink). To make a fan grill I used a plastic computer dust filter screen and snipped a little square out to cover the fan then poked holes in it with a hot screwdriver for the mounting screws. I stuck the capacitors to the back of the esc with double sided tape and strapped the on/off switch to the battery cable. (always check your electronics for proper operation before making any modification to catch any possible warranty issues as the modification will make any warranty claims difficult so make sure it works first.)

Works well out of the box with factory settings. I disassembled the Esc to inspect it and found that there is no way this esc is waterproof, it works well and is assembled well but there is no protection on the sensitive electronics in the case. To get proper water resistance you will need to take the esc heatsink and case off and coat everything in liquid electrical tape (except for the mosfets touching the heatsink). To make a fan grill I used a plastic computer dust filter screen and snipped a little square out to cover the fan then poked holes in it with a hot screwdriver for the mounting screws. I stuck the capacitors to the back of the esc with double sided tape and strapped the on/off switch to the battery cable. (always check your electronics for proper operation before making any modification to catch any possible warranty issues as the modification will make any warranty claims difficult so make sure it works first.)

Works well out of the box with factory settings. I disassembled the Esc to inspect it and found that there is no way this esc is waterproof, it works well and is assembled well but there is no protection on the sensitive electronics in the case. To get proper water resistance you will need to take the esc heatsink and case off and coat everything in liquid electrical tape (except for the mosfets touching the heatsink). To make a fan grill I used a plastic computer dust filter screen and snipped a little square out to cover the fan then poked holes in it with a hot screwdriver for the mounting screws. I stuck the capacitors to the back of the esc with double sided tape and strapped the on/off switch to the battery cable. (always check your electronics for proper operation before making any modification to catch any possible warranty issues as the modification will make any warranty claims difficult so make sure it works first.)

ピニオンとモーターマウントの両方に合うと非常に満足しています。 納品に10日かかった

Very happy with it fits both pinion and motor mount on my wltoys 12429 and 12428. Delivery took 10 days

ピニオンとモーターマウントの両方に合うと非常に満足しています。 納品に10日かかった

私のカスタムWLtoys 12428の素晴らしいアップグレード。 素晴らしい材料、ファンは多くのパワーを持っています。 わずか20日でポルトガルに到着(Covid-19にもかかわらず)。100%おススメ!!

Great upgrade for my custom WLtoys 12428. Awsome material, the fan have a lot of power. Arrived well packed at portugal in just 20 days (despite covid-19) 100% recomended!!

私のカスタムWLtoys 12428の素晴らしいアップグレード。 素晴らしい材料、ファンは多くのパワーを持っています。 わずか20日でポルトガルに到着(Covid-19にもかかわらず)。100%おススメ!!