.jpg)
招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Q: What are the dimensions of this; how big or small is it?
尋ねた mbogelund に 2019-01-15 08:50:26
回答 (2)
Q: What are the physical dimensions of these resistors - what length and diameter in mm?
尋ねた mbogelund に 2020-02-28 01:00:51
Nico80 Hi! Highest diameter is 1.8mm, min is 1.2 in the middle. Length is 3.5mm. Standard 1:6w resistor size. My Fluke Dmm says the 1% tolerance is there!! 100k=100.0kohm Perfect!
2020-02-29 11:17:45 役に立つ (1)回答 (2)
Q: What is the diameter of the inlet nozzle?
尋ねた mbogelund に 2017-12-21 02:15:52
BG478573815 I have ordered the ID 1848558 hot air gun ,will these fit this gun
2021-10-07 02:45:00 役に立つ (1)回答 (3)
Q: What are the outer diameters of the reduced end of the two reduction nozzles?
尋ねた mbogelund に 2017-12-21 01:50:05
cleres tamanhodo conector: 35 mm
2021-09-11 07:10:20 役に立つ (0)回答 (1)
Q: Are they breadboard friendly?
尋ねた mbogelund に 2017-12-06 02:53:33
fortwonator ifthey are breadboard compatible, the terminals are flexible.
2021-05-08 08:32:23 役に立つ (0)回答 (2)
Q: Will the output voltage stay the same even if I change the load on the output?
尋ねた mbogelund に 2020-07-22 08:20:22
OGHagen Most buck converters when used within limits keep the output voltage pretty well assuming the load increase slowly. A sudden increase in load will usually cause a drop in voltage. However the load vs no-load drop may be significant, so make sure to adjust with a light load. That's what the theory teach us anyways. In practice you will probably see a drop in voltage on the output if you increase the load. How much depends on the load.
2020-09-06 08:17:12 役に立つ (1)回答 (2)
mbogelund
15/07/2020
mbogelund
15/07/2020
mbogelund
20/06/2020
mbogelund
20/06/2020
mbogelund
20/06/2020
mbogelund
20/06/2020
mbogelund
20/06/2020
mbogelund
12/03/2020
mbogelund
29/02/2020
尋ねた controltermico1 に 2019-03-04 06:29:36
mbogelund Compro uno de estos y llegado. Si no llega, puedes enviar una reclamacion, y vas a tener tu dinero.
2020-02-27 05:15:29 役に立つ (0)回答 (1)
Q: what is maximum depth measured by this?
尋ねた himanshusharma0 に 2019-04-18 01:55:35
mbogelund That's not how it works, it's not a distance sensor. It doesn't measure the distance from where it's installed to where the water surface is. It measures whether there is water where it's installed or not. So you can for example install it below normal water level and get a message when the water level drops below that point, or install it above normal water level and get a message when the water rises to that point.
2020-02-27 05:09:27 役に立つ (0)回答 (1)
babapro31 width 10cm excluding wheel
2022-05-14 02:45:43 役に立つ (0)