ucfnf
Q: can I bind this to my jumper t18?if so whats the protocol?
diminta oleh MRFLYHIGH di 2021-04-08 08:55:13
Q: what is the flying control range?
diminta oleh BG173625121 di 2020-11-22 05:43:54
ucfnf The receiver is a RadioLink R8FM. RadioLink says, the control distance is 2000 meters in the air.
2021-03-08 12:44:31 Bermanfaat (1)Q: What's the recommended batt for the hook extra 300-h
diminta oleh BG505034171 di 2021-03-02 07:34:31
ucfnf User manual recommand 4S Li-Po Battery 14,8 V 1500 -2200 mAh.
2021-03-03 12:41:17 Bermanfaat (1)Q: Is there a throttle pinout on this board to use a brushless ESC?
diminta oleh cvflyer di 2021-02-16 08:29:30
ucfnf Sorry no, there are only 2 pinouts to connect and throttle a brushed motor.
2021-02-16 01:20:33 Bermanfaat (0)Q: Can be bind with Jumper T12 ?
diminta oleh popad di 2021-02-06 10:41:17
ucfnf You need the Volantex protocol " V 761". If it´s not supported, try to load it from multi-module.org
2021-02-08 04:58:51 Bermanfaat (0)Q: where can i find more references / study about this?
diminta oleh freecarve di 2021-01-30 02:30:40
ucfnf I think it´s comparable with the Fisher Wallace stimulator, see fisherwallace.com and their product reviews for more information.
2021-01-31 11:59:37 Bermanfaat (0)Q: Do I need to have 2 antennas attached? Can I run it with only 1 antenna?
diminta oleh Tomas di 2021-01-13 05:53:53
ucfnf Yes, it will run with only 1 antenna, I tested it. There is only one receiver inside, which switch to the antenna with the best signal.
2021-01-15 09:49:26 Bermanfaat (0)Q: Is the Razor compatible with a Radiomaster TX16S?
diminta oleh Gilles di 2021-01-07 10:08:23
ucfnf Yes, use the protocol RadLink Air and push the tiny binding switch of the receiver.
2021-01-11 01:01:15 Bermanfaat (0)Q: what transmitters works with the receiver in the RTF
diminta oleh BG441854224 di 2020-09-23 01:21:04
ucfnf The included TX is a RadioLink TX with eachine label. The receiver works also with each TX with Open TX Multi protocol. The protocol is: RadLink Air. The receiver is hidden under the FC. Pull out and push the tiny binding switch for binding.
2021-01-04 09:51:17 Bermanfaat (1)Q: Which protocol is used by the included RX / Tx?
diminta oleh kieber di 2020-11-20 10:37:49
ucfnf Works with OpenTx Multi protocol, latest update:" RadLink Air ". You must pull out the receiver -its under the FC- to push the tiny binding switch. Don´t forget the Fine Tuning.
2021-01-04 09:31:55 Bermanfaat (0)Kami dengan tulus mengundang Anda untuk berlangganan email Invite Answer!
Jika Anda berlangganan, kami akan mengundang Anda melalui email untuk menjawab pertanyaan orang-orang tentang produk. Dengan berlangganan, Anda juga akan mendapatkan "Lencana Bermanfaat "! Anda dapat berhenti berlangganan kapan saja di halaman pengaturan privasi.
Bantu orang lain dan jadilah lebih bahagia!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ucfnf It´s a RadioLink receiver and it works with OpenTx Multi protocol, latest update: "RadLinkAir". You must pull out the receiver-its under the FC- to push the tiny binding switch. Don´t forget the Fine Tuning.
2021-04-15 08:15:23 Bermanfaat (0)