Карбюратор на вид и по качеству литья хороший, только на фотографии он с латунной заслонкой, пришёл карбюратор с черной вроде алюминиевой заслокой, и на нем нету надписи микуни, будут устанавливать на мотоцикл ява 638, как установлю напишу как и что.

Карбюратор на вид и по качеству литья хороший, только на фотографии он с латунной заслонкой, пришёл карбюратор с черной вроде алюминиевой заслокой, и на нем нету надписи микуни, будут устанавливать на мотоцикл ява 638, как установлю напишу как и что.

Карбюратор на вид и по качеству литья хороший, только на фотографии он с латунной заслонкой, пришёл карбюратор с черной вроде алюминиевой заслокой, и на нем нету надписи микуни, будут устанавливать на мотоцикл ява 638, как установлю напишу как и что.

gostei

gostei

gostei

I installed this carburetor in a KMX125. The bike started immediately. There is a connector for a vacuum, or oil, line at the front of the carburetor. This needs to be blocked off if not used. The bike ran very well after adjusting the air, and idle screws. I was surprised that no further adjustment was needed. This seem to be a copy of a Mikuni VM26 carburetor. Note on the one photo that the lid of the slide of the Mikuni fitted on this carburetor. The finish is not the highest quality, but much better than expected. Jets are not marked, but the selection seems to be spot on. My altitude is about 1400 meters (4600 feet). The bike also smokes less ( it's a two stroke), indicating better fuel burn. The OEM replacement would have cost me about 12 time more, thus I rate this product as EXCELLENT. 10 stars if I could. Very impressed so far.

I installed this carburetor in a KMX125. The bike started immediately. There is a connector for a vacuum, or oil, line at the front of the carburetor. This needs to be blocked off if not used. The bike ran very well after adjusting the air, and idle screws. I was surprised that no further adjustment was needed. This seem to be a copy of a Mikuni VM26 carburetor. Note on the one photo that the lid of the slide of the Mikuni fitted on this carburetor. The finish is not the highest quality, but much better than expected. Jets are not marked, but the selection seems to be spot on. My altitude is about 1400 meters (4600 feet). The bike also smokes less ( it's a two stroke), indicating better fuel burn. The OEM replacement would have cost me about 12 time more, thus I rate this product as EXCELLENT. 10 stars if I could. Very impressed so far.

I installed this carburetor in a KMX125. The bike started immediately. There is a connector for a vacuum, or oil, line at the front of the carburetor. This needs to be blocked off if not used. The bike ran very well after adjusting the air, and idle screws. I was surprised that no further adjustment was needed. This seem to be a copy of a Mikuni VM26 carburetor. Note on the one photo that the lid of the slide of the Mikuni fitted on this carburetor. The finish is not the highest quality, but much better than expected. Jets are not marked, but the selection seems to be spot on. My altitude is about 1400 meters (4600 feet). The bike also smokes less ( it's a two stroke), indicating better fuel burn. The OEM replacement would have cost me about 12 time more, thus I rate this product as EXCELLENT. 10 stars if I could. Very impressed so far.

Хороший карбюратор. Устанавливал на восход 3, двигатель стал работать ровнее и мягче. Подробнее можно почитать в обзоре http://bikepost.ru/blog/57543/Mikuni-kitajskij-s-yamaha-dt-175-na-voskhod.html

Хороший карбюратор. Устанавливал на восход 3, двигатель стал работать ровнее и мягче. Подробнее можно почитать в обзоре http://bikepost.ru/blog/57543/Mikuni-kitajskij-s-yamaha-dt-175-na-voskhod.html

Хороший карбюратор. Устанавливал на восход 3, двигатель стал работать ровнее и мягче. Подробнее можно почитать в обзоре http://bikepost.ru/blog/57543/Mikuni-kitajskij-s-yamaha-dt-175-na-voskhod.html

gostei muito do produto excelete

gostei muito do produto excelete

gostei muito do produto excelete

I ordered this carburetor for my DT 50 LC with a 47 mm cylinder bore (80 cc) because the stock carb wasn't keeping up with the cylinder new needs. It performs quite nicely but it's not easy to tune for an unexperienced user. I won't give it 5 stars because the first one that I got broke the idle screw and the supplier was a bit difficult about sending a replacement item, which I ended up on receiving when I did a video showing the problem. You can see the videos here: Unboxing https://www.youtube.com/watch?v=wiNt6k49zTo&t=2s Broken screw https://www.youtube.com/watch?v=JUGgtBxvd2o

I ordered this carburetor for my DT 50 LC with a 47 mm cylinder bore (80 cc) because the stock carb wasn't keeping up with the cylinder new needs. It performs quite nicely but it's not easy to tune for an unexperienced user. I won't give it 5 stars because the first one that I got broke the idle screw and the supplier was a bit difficult about sending a replacement item, which I ended up on receiving when I did a video showing the problem. You can see the videos here: Unboxing https://www.youtube.com/watch?v=wiNt6k49zTo&t=2s Broken screw https://www.youtube.com/watch?v=JUGgtBxvd2o

I ordered this carburetor for my DT 50 LC with a 47 mm cylinder bore (80 cc) because the stock carb wasn't keeping up with the cylinder new needs. It performs quite nicely but it's not easy to tune for an unexperienced user. I won't give it 5 stars because the first one that I got broke the idle screw and the supplier was a bit difficult about sending a replacement item, which I ended up on receiving when I did a video showing the problem. You can see the videos here: Unboxing https://www.youtube.com/watch?v=wiNt6k49zTo&t=2s Broken screw https://www.youtube.com/watch?v=JUGgtBxvd2o

Dobra konstrukcja to 125-calowy zawór malossi. Działał dobrze, ale zdjąłem go, bo znalazł go w błocie, chce kąta wprowadzenia tego skutera

Καλη κατασκευη το εβαλα σε ενα typhoon 125 με malossi reed valve δουλεψε μια χαρα αλλα το εβγαλα γιατι έβρισκε στον λασπωτηρα,θελει μια γωνιακη εισαγωγη για στο συγκεκριμενο σκουτερ

Dobra konstrukcja to 125-calowy zawór malossi. Działał dobrze, ale zdjąłem go, bo znalazł go w błocie, chce kąta wprowadzenia tego skutera

Idealne 100%

perfect 100%

Idealne 100%

💯👍

💯👍

💯👍

Idealnie

perfect

Idealnie