Kundenbewertungen

Eine Bewertung schreiben
  • Alle Bewertungen (910)
  • Bild (86)
  • Video (1)
  • Alle Sterne
    • Alle Sterne(910)
    • 5 Sterne(867)
    • 4 Sterne(35)
    • 3 Sterne(6)
    • 2 Sterne(0)
    • 1 Sterne(2)
Sortiere durch:
Zur Vorschau
  • Zur Vorschau
  • Am hilfreichsten
  • Die letzten
Bewertungen nur aus Ihrem Land (United States)
|
Original zeigen

Ein Teil der Rezension wurde automatisch übersetzt.

  • 04/02/2020

    Coole kleine Anzeige, aber Vorsicht, dass es eine "tote" Reihe von Pixeln zwischen den gelben und blauen Teilen. Der Treiberchip ist NICHT SSD136 wie die Beschreibung sagt, seine SSD1306. Ich habe es mit einer ESP32 und Adafruit_SSD1306 Bibliothek verwendet und es funktioniert gut, wenn man die Adresse 0x3C und OLED_RESET -1 anstelle der Standardwerte in den Beispielen verwendet.

    Kommentar (1)
    Original zeigen
  • 18/11/2019

    These OLEDs are my go-to displays now for my projects. Way better than LCD displays. In this particular one, the top 16 pixels are yellow and the rest are blue. I2C only needs 4 wires. The SSD1306 (not SSD136) library is easy to use. There are tutorials everywhere on how to use these. Remember the address on these is usually 0x3C. I ordered some plastic shells for these displays - can't wait to get them! Here's some sample code for how I made the display on an Arduino: /************************************************************************** Display Banggood BLUE/YELLOW OLED **************************************************************************/ #include #include #include #include #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels // Declaration for an SSD1306 display connected to I2C (SDA, SCL pins) #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT,&Wire,OLED_RESET); void setup() { Serial.begin(9600); display.begin(SSD1306_SWITCHCAPVCC, 0x3C); display.clearDisplay(); display.setTextColor(WHITE); } void loop() { display.clearDisplay(); display.drawRect(0, 0, 128, 64, WHITE); display.fillRect(0,0,128,64,WHITE); display.setCursor(0,0); display.setTextColor(BLACK); display.setTextSize(2); display.print(" YELLOW"); display.setCursor(0,32); display.setTextColor(BLACK); display.print(" BLUE"); display.display(); }

    Kommentar
    Original zeigen
  • 17/11/2019

    Very convenient for projects where a small and simple yet powerful display is needed and requiring only 2 wires to control, it can be used with many small micros. Its wide supply voltage is also very convenient making it suitable for 3.3V and 5V systems. Many tutorials and libraries for using this module can be found around the internet.

    Kommentar
    Original zeigen
  • 07/01/2021

    Endlich OLED in einer Box. Die letzten 3 Male kam der OLED gebrochen, aber diesmal in einwandfreiem Zustand. Arbeitet wie erwartet. Die gelbe Farbe ist nur an der Spitze, der Rest OLED hat blaue Farbe.

    Kommentar
    Original zeigen
  • 10/04/2015

    Très bon produit, très lumineux et très compact. Vidéo tutorial: https://www.youtube.com/watch?v=A9EwJ7M7OsI Compatible avec librairie Adafruit_SSD1306_OLED et Adafruit_GFX https://github.com/adafruit/Adafruit_SSD1306 https://github.com/adafruit/Adafruit-GFX-Library Connexions: VCC: 3.3V ou 5V GND: GND Arduino SCL: Pin A5 (Arduino UNO) SDA: Pin A4 (Arduino UNO)

    Kommentar (1)
    Original zeigen
  • 28/02/2018

    The display arrived very quickly. Packaging was effective. I connected it to an Arduino Nano and with the u8g2 libraries (U8G2_SSD1306_128X64_NONAME_1_HW_I2C) it worked just fine. The first upper lines are in yellow, with the lower in light blue. Between the two color areas there are apparently no pixels, so when drawing an image spanning the areas it appears 'separated' (see photos). Knowing that, the display is bright, very clear, sharp and readable (if you have good eyesight, 0.96 inch is tiny !).

    Kommentar
    Original zeigen
  • 20/05/2017

    Very clear and easy to read display. Easy to drive with 5V and Arduino library from Adafruit with I2C address set to 0x3C. Note that this display is monochromatic, meaning that the pixels are fixed single color with top section only being yellow and bottom being blue.

    Kommentar
    Original zeigen
  • 10/05/2016

    Very small (display itself 15*27mm) but very sharp display. Great contrast. Tested it with arduino nano and adafruit ssd1306 library (https://github.com/adafruit/Adafruit_SSD1306). Set I2C-address in sketch to 0x3C (not 0x3D) and connect A4 to SDA and A5 to SCL and display works like a dream. NOTE: Also needs adafruit gfx-library (https://github.com/adafruit/Adafruit-GFX-Library)

    Kommentar
    Original zeigen
  • 08/10/2017

    Perfect for projects that need graphics to be displayed without using too many pins.

    Kommentar
    Original zeigen
  • 09/02/2021

    Ausgezeichnete 2-Farb-Bildschirm. Ich benutze es für den Hotspot zusammen mit mmdvm und die Himbeere pi Null w. Sehr scharf und hell. Ich empfehle es.

    Kommentar
    Original zeigen
Show:

    Gesamt 0 Seiten

    Zur Seite gehen

    Sie interessieren sich vielleicht für:

    recommendation for you
    • US$5.99
    • US$9.99
    • US$6.99
    • US$9.99
    • US$24.99
    • US$8.99
    • US$12.99
    • US$14.99
    • US$6.99
    • US$13.99
    • US$11.99
    • US$11.99
    • US$55.99
    • US$9.23
    • US$14.99
    • US$8.50
    • US$38.99
    • US$69.99