vlgligor
Q: Is it made of aluminium or plastic? What parts are plastic and what aluminium?
gevraagd door vlgligor op 2022-11-11 02:05:07
Kithuru Metal
2022-11-13 09:26:22 Nuttig (0)Q: Besides being electroplated, what material is the heating block made from? Copper, aluminium, other?
gevraagd door vlgligor op 2021-01-19 10:49:20
Loneman It's made from an alloy of chinesuminium, chinganese, jinkyzinc and a large percentage of knockoffalotium along with a small amount of nottalottacoppa. You know, the same quality stuff as in many of the Eastern "clones". ;D
2021-11-15 01:05:11 Nuttig (5)
Q: Is the block copper as claimed
gevraagd door Peregrin op 2020-11-11 02:48:23
vlgligor As mentioned by Peregrin in his review, is anodized aluminium, not copper, although in description is mentioned "hot block Nickel plating copper alloy". I would like also a clarification from seller.
2021-01-20 02:54:24 Nuttig (0)Q: how much does 1 strip weigh ?
gevraagd door aoester op 2021-01-11 01:29:16
vlgligor about 2.1 g for a module
2021-01-11 06:36:10 Nuttig (0)
Q: Can be use for iPhone or Macbook?
gevraagd door Kan Zai op 2020-07-22 05:48:07
vlgligor It has the pentalob heads P2 & P5 bits that are used in Apple phones, but it might not be enough for a full service.
2020-07-24 07:50:23 Nuttig (0)Q: Is it a useful kit for drones?
gevraagd door jaimeportelat op 2020-03-02 06:08:15
vlgligor It has too many bits that are not at all useful for drones (probably just 4 to 6 bits out of 24) and is missing the hex sockets for M3, M2.5 & M2 nuts.I would be looking for something else to use with drones, or you should buy additional bits that are not going to fit inside the case.
2020-07-24 07:47:16 Nuttig (0)
vlgligor Max continuous current for Sunnysky V3508 700kv is 31A with a 1447 prop or 30.5A with a 1555 prop. With smaller props the max current will be under 30A all the time, so there should be no problem for this ESC to run it. Attention, the motor support max 4S LiPo's.
2020-07-21 03:56:22 Nuttig (0)
vlgligor I installed it together with a Kakute F7 HD flight controller + DJI FPV and iNAV (UART2 => GPS @ 38400 bauds, protocol UBLOX), is working flawlessly. Just follow the pin connections when soldering.
2020-07-15 02:50:05 Nuttig (0)Q: What would I have to add to use lipo s6 batteries?
gevraagd door Mac_Rubio op 2020-04-04 04:07:40
vlgligor Works with 6S LiPo's out of the box, nothing else needed.
2020-06-04 10:15:10 Nuttig (0)Q: Any soldening is required to connect ESC to FC and FC to DJI Air unit?
gevraagd door francescogola op 2019-10-12 06:40:16
vlgligor No soldering required on the FC if using just the Air Unit receiver (with DJI remote), as everything is plug and play. Soldering is required for: - motors and battery plug on the ESC (mandatory) - external receiver with third party remote (optional) - GPS unit (optional) - Buzzer (optional)
2020-06-04 10:13:00 Nuttig (0)
vlgligor The screws coming with the stack are M3.
2020-06-04 10:01:37 Nuttig (0)
We nodigen je van harte uit om je te abonneren op de Invite Answer-e-mail!
Als u zich abonneert, nodigen we u uit via e-mail om vragen te beantwoorden die mensen hebben over producten. Door je te abonneren, verdien je ook de "Behulpzame Badge "! U kunt zich op elk moment uitschrijven op de pagina met privacyinstellingen.
Help anderen en wees gelukkiger!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
