kunde anmeldelser

Skrive en anmeldelse
  • Alle anmeldelser(681)
  • Billede(101)
  • Video(0)
  • All Star
    • All Star(681)
    • 5 stjerne(632)
    • 4 stjerne(43)
    • 3 stjerne(4)
    • 2 stjerne(2)
    • 1 stjerne(0)
Sorter efter:
Top anmeldelse
  • Top anmeldelse
  • Mest nyttige
  • Seneste
Anmeldelser kun fra dit land (United States)
|
Vis originalen

En del af anmeldelsen er automatisk oversat.

  • 05/01/2022

    Purtroppo il pacco è arrivato con un imballo molto scadente, in una busta troppo improvvisata per contenere degli articoli delicati che devono affrontare un viaggio così lungo. Essendo componenti delicati ed accessori per una stampante 3D credo che dovrebbero essere meglio protetti. Spero che quando li monterò sulla stampante non manchino parti e che tutto funzioni bene.

    Kommentarer
    Vis originalen
  • 08/06/2021

    Definitely an upgrade from stock, plastic extruder on Ender 3 V2, those original ones are total crap and break super quickly. It doesn't fit the V2 good out of the box. The inlet connector conflicts wit Z axis lead screw. I had to get rid of it and add a filament guide so the filament isn't scratched by the inlet thread. As other mentioned E steps/mm need recalibration, I had to go from 93 to 138.6 steps. Assembly is pretty straightforward, package came without any instructions though. I advice to use some grease on gears to prevent premature wear. Packaging is very poor, nothing but plastic bags. It's hard to believe nothing was damaged in shipping.

    Kommentarer
    Vis originalen
  • 23/03/2021

    Great product but was unfortunately missing a piece. Messaged Banggood and had a new part shipped within a few days. Took 16 days from CN to NZ. Works great after adjusting esteps up from 93 to 139.

    Kommentarer (2)
    Vis originalen
  • 26/09/2021

    Well made extruder. A nice addition to my Ender 3 V2. I recommend this to make sure the filament is properly pushed to the nozzle. Packaging can be better.

    Kommentarer
    Vis originalen
  • 13/04/2021

    Item arrived in good conditions, no missing parts, packaging was nothing special but doesn’t matter much. So far everything seems solid and nothing broken.

    Kommentarer
    Vis originalen
  • 02/09/2021

    As described. Installed on Anycubic i3 Mega S and getting rid of the factory plastic Titan extruder (replica). after installation, e-steps calibration is needed to tune your 3d printer properly. Printing quality improved, minimize under extrusion issues and noise. i totally recommend this extruder!!

    Kommentarer
    Vis originalen
  • 24/12/2021

    Arrived amazingly quickly (less than a week) and looks great. A similar one on another site was 4 times as much so happy with the price. Yet to install but that’ll be a fun post holiday season project

    Kommentarer
    Vis originalen
  • 06/12/2021

    Igényes, sorjamentes kidolgozás, minden alaktrész a csomagban van. Nem mellesleg jól is néz ki a nyomtató vele. :D

    Kommentarer
    Vis originalen
  • 30/07/2021

    easy to install read some other comments and i also changed the e steps to 138,6 works great also some people said that the inlet was touching the z threaded bar all i did was to tighten the socket so one of the flats was next to the bar .

    Kommentarer
    Vis originalen
  • 13/04/2021

    this feeder actually is better than the original one that came with the Ender3. The only problem that I have is that my extruder gear was lil short but I glued it so it’s fine

    Kommentarer
    Vis originalen
Show:

    Total 0 sider

    Gå til side

    Du er måske interesseret i

    recommendation for you
    • US$21.99
    • US$4.99
    • US$9.99
    • US$7.78
    • US$19.99
    • US$44.99
    • US$57.99
    • US$199.00
    • US$8.99
    • US$3.99
    • US$2.09
    • US$42.99
    • US$1.99
    • US$23.31
    • US$42.99
    • US$2.39
    • US$11.99
    • US$3.19