PTFE-belagt motorledningsskrue T8-ledning 2/8mm pitch 2 mm POM-møtrik til Ender-3-serien/CR-10-serien/Sidewinder 3D-printerdel Anmeldelser - Banggood Danmark Online Shopping

PTFE-belagt motorledningsskrue T8-ledning 2/8mm pitch 2 mm POM-møtrik til Ender-3-serien/CR-10-serien/Sidewinder 3D-printerdel

US$6.66
~~US$22.99~~
Køb nu

kunde anmeldelser

5 ud af5

Se alle5 anmeldelser

5 stjerne
5 (100.0%)
4 stjerne
0 (0%)
3 stjerne
0 (0%)
2 stjerne
0 (0%)
1 stjerne
0 (0%)

Skrive en anmeldelse Få dobbelt anmeldelse point, hvis du er en af de første 3 anmeldelser udgivet!

Alle anmeldelser(5)
Billede(2)
Video(0)
All Star
- All Star(5)
- 5 stjerne(5)
- 4 stjerne(0)
- 3 stjerne(0)
- 2 stjerne(0)
- 1 stjerne(0)

Sorter efter:

Top anmeldelse

Top anmeldelse
Mest nyttige
Seneste

Anmeldelser kun fra dit land (United States)

|

Vis originalen

En del af anmeldelsen er automatisk oversat.

Nachiket MhatreVIP3
IN
07/11/2021

Please don't waste your time on these. The machining quality of the lead screw is appalling, with uneven pitch all round. This is evident through cyclic binding with the lead screw nut. This problem was evident in both pairs of lead screws and nuts I had purchased, so this isn't mere coincidence. In fact, other nuts also bind on these lead screws, whereas the supplied nuts don't bind with other lead screws. If you buy these lead screws and install in your printer, that axis will experience massive binding and wobble. You are going to hurt both quality and durability of your 3D printer by using this product. Avoid this like the plague.

Please don't waste your time on these. The machining quality of the lead screw is appalling, with uneven pitch all round. This is evident through cyclic binding with the lead screw nut. This problem was evident in both pairs of lead screws and nuts I had purchased, so this isn't mere coincidence. In fact, other nuts also bind on these lead screws, whereas the supplied nuts don't bind with other lead screws. If you buy these lead screws and install in your printer, that axis will experience massive binding and wobble. You are going to hurt both quality and durability of your 3D printer by using this product. Avoid this like the plague.

Please don't waste your time on these. The machining quality of the lead screw is appalling, with uneven pitch all round. This is evident through cyclic binding with the lead screw nut. This problem was evident in both pairs of lead screws and nuts I had purchased, so this isn't mere coincidence. In fact, other nuts also bind on these lead screws, whereas the supplied nuts don't bind with other lead screws. If you buy these lead screws and install in your printer, that axis will experience massive binding and wobble. You are going to hurt both quality and durability of your 3D printer by using this product. Avoid this like the plague.
2

Kommentarer

Vis originalen
MadarMVIP3
HU
13/05/2021

Everything was OK!

Everything was OK!

Everything was OK!
0

Kommentarer

Vis originalen
mkubatVIP5
BA
18/10/2021

okk

okk

okk
0

Kommentarer

Vis originalen
mkubatVIP5
BA
20/09/2021

Videcemo

Videcemo

Videcemo
0

Kommentarer

Vis originalen
blake2244VIP2
US
29/04/2021

very nice. great upgrade and and they look good too!

very nice. great upgrade and and they look good too!

very nice. great upgrade and and they look good too!
0

Kommentarer

Vis originalen

Show:

Total 0 sider

Gå til side

Gå

Du er måske interesseret i

recommendation for you