Hodnocení zákazníků

Napsat recenzi
  • Všechny recenze(811)
  • Snímky
  • Video(1)
  • Hvězdný
    • Hvězdný(811)
    • Hvězda 5(736)
    • Hvězda 4(46)
    • Hvězda 3(16)
    • Hvězda 2(8)
    • Hvězda 1(5)
Seřazeno podle:
Nejlepší recenze
  • Nejlepší recenze
  • Nejvíce užitečné
  • Nejnovější
Recenze pouze z vaší země (United States)
Ukázat originál

Část recenze byla přeložena automaticky.

  • 08/06/2021

    Principal peça do pedido, farei a montagem tão logo possa. Chegou após 17 dias do pedido. Qualidade da PCB excelente.

    Ukázat originál
  • GijVIP4

    C'è tutto! Quindi, spero che funzionerà, non vedo il perché non dovrebbe. Al momento non ho avuto occasione di montarlo. Eventualmente, se ha bisogno di modifiche, seguirò i consigli degli altri utenti.

    Komentáře (1)
    Ukázat originál
  • 17/02/2021

    chegou dentro dos 30 dias bem menos, só falta montar e testar..fui..kkkk

    Ukázat originál
  • 31/12/2021

    Very fast delivery! All is OK!

    Ukázat originál
  • 17/08/2021

    j'ai reçu l'article avec un peu de retard en bonne état je n'ai pas encore fait le montage Merci Banggoood

    Ukázat originál
  • 07/04/2021

    The shipment contained two sockets and was without a pic ... how do I get to the pic?

    Komentáře (1)
    Ukázat originál
  • 14/07/2021

    Perfect, Easy to build and worked first time

    Ukázat originál
  • 31/05/2021

    Great product, I recommend!

    Ukázat originál
  • 23/07/2017

    It is unexpectedly accurate for the price. However, my kit had the wrong size IC socket. It was a 16 pin socket instead of an 18 pin. Fortunately I have a huge supply of parts so I created a socket out of a machined header strip. I couldn't see making an issue out of a 30 cent part. Plus the instructions are barely adequate. You basically have depend on the silkscreen for part placement. To build it I used a fine soldering tip and AlphaMetals .015" no clean solder. I also recommend wearing an anti-static wrist strap while handling the parts. Despite being no-clean solder I cleaned the board anyway with 91% Isopropanol. Testing was problematic as there is no indication of what the signal level should be. The counter needs approx. 3v peak to work. Once it locked the accuracy was comparable to the readout accuracy of my O'Scope. I also tested it with a 3.58 MHz xtal and the reading was within the tolerance of the xtal. I intend to use this as a readout for my DDS RF source and will probably buffer the input with a home brew cascode JFET amplifier. I am willing to share my notes about this product if anyone has questions or difficulties.

    Komentáře (2)
    Ukázat originál
  • 03/07/2017

    I am very surprised with this tester/counter. Good quality parts (all parts are marked!) metal film resistors, low drop low power voltage regulator (good for battery). Very good PCB with solder stop mask and high quality shining tinning. Rounded edges of the PCB made of FR4. And the first time on a kit from china with a montage description in paper form! The housing is perfectly suitable too. Does it work as tester for crystals? YES! Does it work as frequency counter? YES! Would I buy this again? Of course! The power consumption is about 20 to 25 mA.

    Ukázat originál

    Celkový 0 stránky

    Jdi na stránku

    Možná vás zajímá

    recommendation for you
    • US$4.99
    • US$4.59
    • US$22.99
    • US$9.99
    • US$18.99
    • US$27.99
    • US$12.99
    • US$26.99
    • US$3.99
    • US$21.99
    • US$6.99
    • US$13.99
    • US$7.99
    • US$24.99
    • US$10.99
    • US$15.99
    • US$74.99
    • US$12.99