Excelente producto, Llegada rápida, 12 días

Excelente producto, Llegada rápida, 12 días

Excelente producto, Llegada rápida, 12 días

Sehr gute Fräser mit 1/8" Aufnahme und auch 1/8" Schneide. Ich fräse momentan Eiche und Buche massiv damit, was einwandfrei funktioniert. Sehr glatte Fräskanten und sauberer Rundlauf. Die 3.175mm Fräser habe ich sonst nirgends gefunden. Glatte Schulnote 1!

Sehr gute Fräser mit 1/8" Aufnahme und auch 1/8" Schneide. Ich fräse momentan Eiche und Buche massiv damit, was einwandfrei funktioniert. Sehr glatte Fräskanten und sauberer Rundlauf. Die 3.175mm Fräser habe ich sonst nirgends gefunden. Glatte Schulnote 1!

Sehr gute Fräser mit 1/8" Aufnahme und auch 1/8" Schneide. Ich fräse momentan Eiche und Buche massiv damit, was einwandfrei funktioniert. Sehr glatte Fräskanten und sauberer Rundlauf. Die 3.175mm Fräser habe ich sonst nirgends gefunden. Glatte Schulnote 1!

They came as shown, I did a runout test and vibration/balance test to compare to my onsurd bits. Run out was the same on the shank I could not compare the tip due to a single flute, but seems fine @ 18,000 rpm they did seem to make a bit of a different harmonic then the Onsurd but I would not say a balance issue more I think the way the air was interacting with it. Speed and feeds were the same as Onsurd in HDPE really the only difference were pocket floors were not as clean with some engine turning marks which could be a pro or con depending on your work. But with a few speed n feed tweaks I bet I could get them cleaned up but threw cut sidewalls where perfect. The big take away is i got 10 for less then one Onsurd so even if they wear faster or i crash one the value is there. I am a big believer in good tooling in metal, but for woods and plastics I'm willing to try value bits and these do make sense for general riping. Tested on a Multicam router

They came as shown, I did a runout test and vibration/balance test to compare to my onsurd bits. Run out was the same on the shank I could not compare the tip due to a single flute, but seems fine @ 18,000 rpm they did seem to make a bit of a different harmonic then the Onsurd but I would not say a balance issue more I think the way the air was interacting with it. Speed and feeds were the same as Onsurd in HDPE really the only difference were pocket floors were not as clean with some engine turning marks which could be a pro or con depending on your work. But with a few speed n feed tweaks I bet I could get them cleaned up but threw cut sidewalls where perfect. The big take away is i got 10 for less then one Onsurd so even if they wear faster or i crash one the value is there. I am a big believer in good tooling in metal, but for woods and plastics I'm willing to try value bits and these do make sense for general riping. Tested on a Multicam router

They came as shown, I did a runout test and vibration/balance test to compare to my onsurd bits. Run out was the same on the shank I could not compare the tip due to a single flute, but seems fine @ 18,000 rpm they did seem to make a bit of a different harmonic then the Onsurd but I would not say a balance issue more I think the way the air was interacting with it. Speed and feeds were the same as Onsurd in HDPE really the only difference were pocket floors were not as clean with some engine turning marks which could be a pro or con depending on your work. But with a few speed n feed tweaks I bet I could get them cleaned up but threw cut sidewalls where perfect. The big take away is i got 10 for less then one Onsurd so even if they wear faster or i crash one the value is there. I am a big believer in good tooling in metal, but for woods and plastics I'm willing to try value bits and these do make sense for general riping. Tested on a Multicam router

Very good mills router bit .

Very good mills router bit .

Very good mills router bit .

excelentes

excelentes

excelentes

Very good tool for multiwood cutting. Finishing was good. Only check the type of material, and one setting in tool options as "climb" or "Conventional". Some material, choose climb option for edge finishing. And some conventional option for best finishing. And ACP cutting was good. All products are very good. And also good quality. I experienced the tools are too good to use in my router machine. The products were delivered early as the possible time. Also like that fast delivery.

Very good tool for multiwood cutting. Finishing was good. Only check the type of material, and one setting in tool options as "climb" or "Conventional". Some material, choose climb option for edge finishing. And some conventional option for best finishing. And ACP cutting was good. All products are very good. And also good quality. I experienced the tools are too good to use in my router machine. The products were delivered early as the possible time. Also like that fast delivery.

Very good tool for multiwood cutting. Finishing was good. Only check the type of material, and one setting in tool options as "climb" or "Conventional". Some material, choose climb option for edge finishing. And some conventional option for best finishing. And ACP cutting was good. All products are very good. And also good quality. I experienced the tools are too good to use in my router machine. The products were delivered early as the possible time. Also like that fast delivery.

Reçues rapidement Une fraise cassée ...ce n'est pas grave , il en reste 9 :)

Reçues rapidement Une fraise cassée ...ce n'est pas grave , il en reste 9 :)

Reçues rapidement Une fraise cassée ...ce n'est pas grave , il en reste 9 :)

Just got these , they look great , can't wait to see how they perform

Just got these , they look great , can't wait to see how they perform

Just got these , they look great , can't wait to see how they perform

Thanks, the package has arrived. 😊

Thanks, the package has arrived. 😊

Thanks, the package has arrived. 😊

Perfetto, come da descrizione.

Perfetto, come da descrizione.

Perfetto, come da descrizione.