طائرة ريموت كونترول TY Model Black Flyer V2 بالألياف الكربونية مزودة بنظام الطاقة
تمت ترجمة جزء من المراجعة تلقائيًا.
I've built and flown all of the Black Flyers: V1, V1.1 and V2. The V1 Is an excellent flyer, but the packaging means that some of the carbon can be broken in the post. The V1.1 and the V2 have improved packaging and a better wing fixing. The V1.1 is very similar to the V1 buthas an increased wing chord giving more wing area. Getting to the V2, it goes together well but, like the V1.1 it has a flat plate wing(s) which require great care in covering to avoid warping. It also means that the lack of wing section combined with the all flying tailplane means that the elevator is very sensitive and trim is critical. Both the V1.1 and V2 have a tendency to 'tuck' and dive into the ground. I feel that this is a design fault and they should have retained the cambered wing. On a value for money basis, you can't beat any of them. Weights with battery: V1 13.5 gm, V1.1 18 gm, V2 18 gm. All covered with tissue, not the supplied film.
جيد جداً وسهل صنع منشورات داخلية التحدي الأكبر هو المكونات الصغيرة خصوصاً براغي تثبيت المنطقة. سلوك الطيران الخاص بالرحلة النهائية لا تشوبه شائبة. مع 1S 160 مللي أمبير/ساعة، يجلب الوزن الخفيف 23 جرامًا فقط إلى المقياس. كما أن المحرك لديه طاقة كافية ومن الممكن أن يدور على أصغر دائرة نصف قطرها. ومن الممكن تحديد مركز الجاذبية وطول مدة الطيران.
This model went together following the downloaded instructions. As mentioned by others the hardest part was fixing the tiny self tapping screws. Get yourself a very small phillips screwdriver, fit a piece of heat shrink tube on the end to hold the screws while you screw them in. Do all this over a tray with soft cloth inside or you may lose them! I covered my model in crushed silver mylar - to save a little weight and make it look different from the others. It flew dead straight from my hand the first time that I flew it. It flies on half power. It circles tightly and loops easily. Great little model.
Took about 3 hours to put together. Instructions are lacking of course, I ended up using the electronics from a crashed E-Flite SBach so I'm running its a little faster and heavier than it should be but flies pretty good for 19.99. Use a little super glue and this thing can take a crash for sure.
أستلم غرضي لكن لسوء الحظ ليس هناك تعليمات حول كيفية بناء الطائرة, أرجوك أخبرني كيف أفعل شكراً لمساعدتك تحياتي
Everything in the kit went together well. Used 3M spray on adhesive on the wings, tailplane and rudder CF assembies, then stretching the mylar covering on a flat board, and then dropping each assembly onto the mylar. Use a sharp craft knife and run around the outside of each assembly. Quite tricky getting the screws into the blocks that hold the wings in place, but got there in the end. Some more information or recommendations regarding ESC and receiver and servos would be good though
من الصعب بناء أجزاء صغيرة جداً ولكن عندما تنتهي، تبدو مذهلة.
خطأ، حالة، المادة إشتريتُ بشكل واضح كُلّ الأجزاء مَنْ ضمنهم لَهُ فقط لَهُ تَحْطيمهم. حسناً، إتّباع الطلب كان في حالة بدون تعليمات لا شيء وبدون أيّ مكوّن كهربائي لمقبضك المجموع الذي قابلني في نفس المقال الذي اشتريته (الذي وافقت عليه بشكل واضح لتأتي بكل شيء) وأنت غير موجود بالفعل. لدي إعلان آخر بنفس المادة بونيدو الذي لا يأتي مع هذه الأجزاء لكي يجعلك تستلمه في 10 أيام و تقريبا شهرين من المتوقع تَحْصلُ على هذه الحالةِ. لم يتم بناء الصين الثاني وعودة المواد الصينية بشكل غريب (الذي من الواضح لدي في بانتالاسوس) عن سينفيرغنزاس.
The plane arrived in good shape. I plan on using the parts as spares for the plane I have for indoor flying. Neat design, very delicate, but slow flyer for indoor use.
عندما أفتح التسليم أشعر بالحيرة لكن عندما أنظر إلى المحرك والمروحة أدركت أنها يجب أن تكون طائرة إنها مضغوطة حقاً هوب يمكنها إكمال الاجتماع. شكراً لك يا بائع وبانججود.