Customer Reviews

4.92 out of 5
See all 668 reviews
Write a Review
  • All Reviews (668)
  • Image (96)
  • Video (0)
  • All Star
    • All Star(668)
    • 5 Star(620)
    • 4 Star(42)
    • 3 Star(4)
    • 2 Star(2)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
Show Original

A part of the review has been auto-translated.

  • 08/06/2021

    Definitely an upgrade from stock, plastic extruder on Ender 3 V2, those original ones are total crap and break super quickly. It doesn't fit the V2 good out of the box. The inlet connector conflicts wit Z axis lead screw. I had to get rid of it and add a filament guide so the filament isn't scratched by the inlet thread. As other mentioned E steps/mm need recalibration, I had to go from 93 to 138.6 steps. Assembly is pretty straightforward, package came without any instructions though. I advice to use some grease on gears to prevent premature wear. Packaging is very poor, nothing but plastic bags. It's hard to believe nothing was damaged in shipping.

    Show Original
  • 23/03/2021

    Great product but was unfortunately missing a piece. Messaged Banggood and had a new part shipped within a few days. Took 16 days from CN to NZ. Works great after adjusting esteps up from 93 to 139.

    Comments (2)
    Show Original
  • 22/01/2021

    good, I’m happy. packaging could of been better. maybe some bubble wrap. item was just placed in zip lock bag and then into shipping bag with no protection and it’s damaged now the paint chipped off.

    Show Original
  • 26/09/2021

    Well made extruder. A nice addition to my Ender 3 V2. I recommend this to make sure the filament is properly pushed to the nozzle. Packaging can be better.

    Show Original
  • 13/04/2021

    Item arrived in good conditions, no missing parts, packaging was nothing special but doesn’t matter much. So far everything seems solid and nothing broken.

    Show Original
  • 07/01/2021

    Her boss came peeled off and a little crushed. It can be packaged better. 1 star fell. It came quickly, in full. Turkey has reached my hand with Aras Cargo. I advise.

    Show Original
  • 02/09/2021

    As described. Installed on Anycubic i3 Mega S and getting rid of the factory plastic Titan extruder (replica). after installation, e-steps calibration is needed to tune your 3d printer properly. Printing quality improved, minimize under extrusion issues and noise. i totally recommend this extruder!!

    Show Original
  • 13/04/2021

    this feeder actually is better than the original one that came with the Ender3. The only problem that I have is that my extruder gear was lil short but I glued it so it’s fine

    Show Original
  • 15/01/2021

    Delivery a bit long but it's normal given the sanitary conditions. And there are no assembly instructions but a little tutorial on youtube and it's nickel.

    Show Original
  • 30/07/2021

    easy to install read some other comments and i also changed the e steps to 138,6 works great also some people said that the inlet was touching the z threaded bar all i did was to tighten the socket so one of the flats was next to the bar .

    Show Original

    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • US$206.00
    • US$21.99
    • US$4.99
    • US$9.99
    • US$3.99
    • US$19.99
    • US$44.99
    • US$57.99
    • US$199.00
    • US$8.99
    • US$3.99
    • US$33.91
    • US$199.00
    • US$259.00
    • US$53.99
    • US$23.99
    • US$499.99
    • US$107.99