{{$productInfo.reviewAmount.average}} out of 5
| Specification | ||
| Brand name | URUAV | |
| Item name | UR85 | UR85HD |
| Wheelbase | 85mm | 85mm |
| Motor |
Mode: 0805 KV9000 Configu-ration:9N12P Stator Diamter:8mm Stator Length:5mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ10.5mm*17mm Weight(g):3.0g No.of Cells(Lipo):1S-3S |
Mode: 1102 KV9000 Configu-ration:9N12P Stator Diamter:11mm Stator Length:2mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*16mm Weight(g):2.8g No.of Cells(Lipo):1S-3S |
| Camera |
Caddx EOS2 1/3" CMOS Sensor 1200 TVL 2.1mm lens 16:9 Image size NTSC Global WDR Internal Synchronization |
CADDX Turtle V2 Image sensor: 1/2.7" CMOS sensor Horizontal: 800TVL TV system: NTSC/PAL changeable Video Resolution: 1080P@60fps / 1080P@30fps / 720@60fps Power Input: DC 4.5-20V FPV FOV: 155° Recording FOV: 170° Mini Illumination: 0.01lux Image Resolution: 2 Megapixels Lens: 1.8mm Turbo Eye Lens Working Current: 380mA@5V/160mA@12V (low consumption) OSD Menu: Yes (Support Voltage Display) Video Files: MP4 Audio: Support Electronic Shutter : PAL : 1/50-100,000 NTSC : 1/60-100,100 S/N Ratio: >60dB (AGC OFF) Video Output: CVBS Max Micro SD Card Supported: 8-64GB(need Class 10 or above, recommend Class 10/UHS-I/UHS-II) Color: Red |
| Flight controller |
(Frsky version) CRAZYBEE F4FR PRO V2.0 Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEE F4FS PRO V2.0 Firmware target: CrazybeeF4FS (DSM2/DSMX version) CRAZYBEE F4DX PRO V2.0 Firmware target: CrazybeeF4DX (No RX version) CRAZYBEE F4 PRO V2.0 Firmware target: CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-3S battery input (DC 3.5-13V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) DSM2/X Version built-in Serial-based DSM2/DSMX compatible satellite receiver No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection |
|
| Onboard 4in1 ESC |
MCU upgraded to EFM8BB21 Power supply: 1-3S LiPo/LiPo HV (3.5v/13v) Current: 5A continuous peak 6A (5 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.He Default protocol: DSHOT600 |
|
| Frsky NON-EU receiver Version |
SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
|
| Flysky receiver Version |
SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support |
|
| DSM2/DSMX receiver version |
Serial bus receiver Protocol: DSM2/DSMX compatible Channels:6-9 (Depend on your radio) No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
|
| PNP No RX version | No RX version support external serial-bus receiver like xm+, TBS, S-FHSS etc. | |
| VTX |
Output power: 25~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Antenna: RG178 antenna Frequency: 5.8GHz 5bands 40 channels With Raceband Smartaudio ready Weight: 3g |
|
| Lipo Battery |
Capacity:300mAh Voltage:11.4v Continuous Discharge Rate: 40C Instantaneous discharge rate: 80C Size: 65mmx18mmx11mm Weight: 25g Connector: XT30 |
|
| Size | 112mm*112mm*60mm | 112mm*112mm*60mm |
| Weight | 42g(without battery) | 51.4g(without battery) |
| Weight | 67.4g(with Original 3s 300mah Lipo battery) | 76.8g(with Original 3s 300mah Lipo battery) |
| Shipping method(s) | Shipping time | Tracking information |
|---|