Customer Reviews

4.86 out of 5
Write a Review
  • All Reviews (77)
  • Image (19)
  • Video (0)
  • All Star
    • All Star(77)
    • 5 Star(68)
    • 4 Star(7)
    • 3 Star(2)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
  • March-22 2020 07:57:00

    O produto chegou certinho bem embalado, o vendedor enviou com rapidez muito bom trabalho, continue assim. Já a impressora 3D excelente imprimir poucas peças mais já estou contente com os resultados! Não é simples a parte de conectar os cabos a placa mãe, uma dica é olhar as informações que vem no cartão SD antes da montagem porque o manual vem poucas informações!

    Comments (1)
  • July-28 2020 12:32:16

    Ok, let's face it - the printer itself is a great value for money. Fullstop. I won't have a second one ordered if I wasn't satisfied with the first one. Then why is it that I just give 4 stars on this review? Because the mounting holes of the case were drilled with wrong dimensions. Or (maybe even more likely) wrong hinges were included. And thus I can't finish my build - at least not today. :-/ ~16mm spacing for the drilled holes vs ~20mm on the hinges. And the later one somehow don't match the

    December-11 2020 06:52:55

    Très bien emballé. le carton a bien souffert durant le transport mais les éléments en mousse ont bien protégés les pièces. Le montage n'est pas très compliqué, il faut regarder les instruction sur la Micro SD qui comporte une vidéo de montage, une notice un peu plus complète. le mieux est de regarder les vidéos en ligne. Très important, bien contrôler chaque éléments au montage. - les montants n'ont pas tous les mêmes longueurs. chez moi 1 a 2 mm de différence entre les 4. - Vérifier

  • July-14 2020 12:30:27

    Perfecta. Es mi primera coreXY. Tengo una Alfawise u30 que he trasteado mucho. Después de ver unas cuantas review de la Sapphire pro tenia que ser mía. Estoy muy contento. Pensaba que me costaría mas hacerme a la maquina pero nada de eso. Montada en aproximadamente 8h o menos. Recomiendo actualizar firmware. Pongo foto primera impresión, Fantasminiom a 80mm/s algo menos de 2h. Me falta montar el cercado pero quiero hacer alguna mejora antes de eso. Monte en la cama un cristal que no viene con

    Comments (2)
  • April-05 2020 02:37:19

    Questa è la mia prima CoreXY dopo altri modelli cartesiani, devo dire che a parte qualche piccola pecca , rimediabile con una decina di €, nel complesso , se messa nelle.giueste condizioni, stampa discretamente bene, abbastanza silenziosa non invadente come ingombri. Mi piace molto kl Lcd molto reattivo e finalmente a colori. la scheda mks a 32bit v1.2 mi soddisfa. Alcuni bug nel firmware si possono scovare dal menu nella sezione "Altro" dove l intera schermata contiene icone non funzionanti, in

    Comments (1)
  • April-24 2020 19:18:15

    This 3d printer compare with my prusa mk3s it's very good for this price, I recommend, juste some modifications 1st weak hotEnd and extruder but not issue at all I can print PLA and ABS without any problems, I wish this printer had a good silent power supply this without fan or more silent fan the most noisy in this printer but we can handle it for now, print 120mm/s woow this good 😌

  • December-23 2020 02:58:17

    Etwas erschwerter aufbau muss man sich Zeit nehmen aber im groben und ganzen ein geiles Teil. Und hir und da kleine muss mann noch kleine Fehler von Two Trees in Kauf nehmen .

  • December-15 2020 12:24:24

    fui levantar hoje ,finalmente tenho de a montar e testar,mas aconselho,vai ser a minha primeira vez e estou na espetativas muito altas vai ser fascinante

  • June-26 2020 07:51:13

    This 3D printer worked perfectly after assembly which was fairly straightforward. The only issues I had were a slightly warped heat-bed (unfortunate, but still usable), a few slightly loose screws on the Y-axis rails and the Y-axis endstop was mounted back to front.

  • June-14 2020 14:00:28

    This is my first 3d printer. Despite the initial not so good reviews I still believed this machine is the right one for the money, even as the first printer. I wasn't ready to pay premium for the prusa and so far im glad I didn't (wanted core xy anyway). The assembly took me two evenings but I was taking my time. I would say the Z rods have to be carefully done. I recommend assemble them loose first (including rod brackets) them move your bed down, tighten the bottom, move up and tighten the top brackets.


    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • US$399.00
    • US$196.00
    • US$209.99
    • US$209.00
    • US$399.00
    • US$299.00
    • US$279.99
    • US$579.00
    • US$239.99
    • US$289.00
    • US$259.00
    • US$2.39
    • US$23.99
    • US$12.90
    • US$2.49
    • US$21.48
    • US$3.74
    • US$27.80