Customer Reviews

4.96 out of 5
See all 793 reviews
Write a Review
  • All Reviews (793)
  • Image (121)
  • Video (24)
  • All Star
    • All Star(793)
    • 5 Star(763)
    • 4 Star(29)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
|
Show Original

A part of the review has been auto-translated.

  • 10/08/2016

    My first impressions: frame looks pretty good, but has several issues. Slots for camera mount needs to be corrected because assembling is not possible without some sandpaper work. Kit is delivered with too short screws. Screws are exceeding 4 mm plate for less than 2 mm, which is not enough. Also too short screws for vtx antenna mount. And worse thing, holes for FC and PDB are not in good position. Standard is 30.5 mm, and drilled on the frame is under 30 mm. Need to be corrected. Feature (slots) for plastic strap for holding battery connector is too small for anything. Like someone make it without understanding of its purpose. With corrections, it can be a good product

    Comments
    Show Original
  • 12/08/2016

    We all know it's not the original design, the quality of this kit is very nice! And the weight...it's so light!! All the parts that you need are in there and it's ready to assemble. Carbon is a nice mat twill weave. Of course I will sand the edges but they look clean at first glance. Only the extra plate for the lipo is a very rough cut, but who cares... Some tiny holes in the middle of the top plate (where the camera plates will slip in) are a bit to tiny. With some sand paper of file you can make it a bit wider (like one hair...). And for those crazy crashing pilots...maybe you need longer screws. I didn't notice on the picture but they are quite short. It fit, it will hold your stand off perfect, but it won't give the extra strenght. Also a very big thank you to banggood for adding that Matek PDB! At time of the pre-order there was a orange thingy in the picture...now it's a PDB of quality. By the way, I also ordered the Realacc HUBOSD H-Type PDB with OSD...that thing won't fit in the lengts of this frame...it's less than 1mm to long and with thoutch those camera plates. Rotating that H-Type board will work but it will come slightly over the edge of the bottom plate. I'm still considering that...or alter those camera plates to fit that cool PDB.

    Comments
    Show Original
  • 12/08/2016

    The RealAcc X-210 is better known as the Banggood "Charpu-X Clone"; there is no doubt that this is an out & out clone. However, quality appears better than average, and they do include a decent name-brand integrated PDB with 5V/2A switching regulator & 12V/500mA 7812 linear regulator. ESC outputs are rated 25A continuous; figure 30-35A surge current. Frame plates measure out as promised; decent quality CF plate with lots of fine layers indicating no filler. Cut edges are a bit rough with a few slubs, but nothing a few minutes with sandpaper won't cure easily. Advertised weights are quite optimistic; complete kit (everything in the package) weighs in at 110.22 grams. Vital Statisitcs: 4mm Main Plate 2mm Upper Body Plate 1.5mm all camera mount parts and battery armor plate m3 x 30mm Standoffs Weights: Main Plate: 63.77gr All Carbon Fiber Parts: 80.92gr All Hardware: 15.26gr Frame & Hardware: 90.82gr Matek XT60 PDB: 10.09gr Battery Strap & Armor Plate: 10.12gr Full Kit: 110.22gr Bottom line is it's a decent frame particularly at the price point, and I don't regret buying it a bit; I'll certainly get my money's worth of fun out of it. Those of you interested in the Matek XT60 PDB can find it here: http://www.banggood.com/Matek-Systems-PDB-XT60-W-BEC-5V-12V-2oz-Copper-For-RC-Multirotors-p-1049051.html?p=GI031609948520121218

    Comments
    Show Original
  • 03/04/2018

    Once again a great frame from Realacc OK its a copy of the QAV X put its a great one it looks just like it. she is very well made and as with all Realacc frames she comes with a PDB. I have made a small change to the colour..

    Comments (1)
    Show Original
  • 29/06/2017

    Good frame! Had to modify it a bit to be able to fit a 3 layer stack. (see picture)

    Comments
    Show Original
  • 05/10/2016

    и по мне отличного качества - момент с винтами поправили остался только тот факт что распорки не одинаковые 4 поболее и одна чуть меньше - внимательнее - она идет на верх. при этом она все равно больше чем надо на миллиметра два так что надо взять в ручки напильник и чуть ее с боков подпилить тогда корпус идеально собирается. планку сверху я не ставил под гопро которая потому что она номинальная и не дает прочности или нагрузки. а вот добавочку которая сзади под передатчик можно поставить на спейсеры и поместить его наверху между верхней пластиной и этой добавочкой - будет защищить и крепить - это очень удобно. собраный дрон летает просто шоколадно мне все нравится и батарея снизу хороша для флипов и ролов. у него меньше инерции чем у марсианина или там qav210. но собирать надо очень плотно места мало - поэтому рекомендую контроллер LUX с вырезами - это сильно в данном корпусе будет плюс если камера с корпусом как у FOXEER

    Comments
    Show Original
  • 30/11/2016

    I very much like this frame becausevit's very simple and sturdy. It's also very well balanced. Only problem with it, that you realy have to think about how you are going to put it together. There a quite a few tutorials on you tube. One problem that i had was with the camera. Best option is to buy a camera that has connections on top.

    Comments
    Show Original
  • 31/07/2016

    nice design

    Comments
    Show Original
  • 28/05/2017

    The build come out pretty clean and all the ideas "borrowed" from Lumenier are really useful. Buffers on the arms saved my motors couple of times, small holes to ziptie the TX antenna. I would advise to turn PDB's battery contacts to the back and put pair of wires between PDB and XT60 connectors.

    Comments
    Show Original
  • 18/08/2016

    This is just a good "designed" frame with good enought quality, and I just have a couple of things to highlight of this frame that are wrong. First, the screews on the box are not enought long for the lower plate, in my case is the 4mm version, the screews just go 2mm or less into spacers, any small crash can pull apart spacers from lower plate. Second,for the well designed area for a HS1177 cammera and similar its needed to chose those cammeras with bottom connector or you will forced to put cammera at about 60º, good for Matty but not for all occasions. Not enought tested yet, becouse of the forced high angle on the cammera, but at first sign it corners very very well.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$9.00
    • US$20.99
    • US$13.00
    • US$89.99
    • US$139.99
    • US$5.69
    • US$28.99
    • US$3.00
    • US$12.00
    • US$27.99
    • US$6.00
    • US$39.99
    • US$8.99
    • US$13.99
    • US$23.99
    • US$7.99
    • US$3.99
    • US$69.99