Customer Reviews

4.95 out of 5
Write a Review
  • All Reviews (177)
  • Image (40)
  • Video (1)
  • All Star
    • All Star(177)
    • 5 Star(169)
    • 4 Star(7)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
  • 06/11/2020

    I absolutely live this Laser! It was well packaged in foam material with helpful stickers on it. The assembly guide is well made, building the Laser up took me - with this good guide - about 20 minutes. The different steps (6) are accompanied with bags with the step number and the content on it which was really helpful. All in all on of the best self assembly products I ever bought (and as a Maker I usually buy self assembly gear). Focusing the Laser is straightforward with a 2mm Acryl Plate which just needs to be put under the green shield with the gantry screws loosened. Then tight the 2 screws and you are set and done. Cutting in 4mm plywood takes some repetitions but thats fine for a semiconductor laser. Currently I am using Lightburn but I also tested LaserGRBL with success. I am totally happy with the purchase and would give 6 stars if thats possible! 10/10 would buy again!

    Comments (4)
  • 14/10/2020

    Five star build quality, all-metal-frame, easy to assemble, works great. Pros: - The fan is running all the time reminding you it's live and loaded. Great for reducing unexpected fires from forgotten lasers and the constant speed also extends the lifespan of the fan. - The laser is focused by raising/lowering the whole engraving head which is less fiddly than the alternatives where you have to grab a focus ring underneath the laser. For the best focus you have to lower the head as close to the material as you can. This also ensures the green plastic protection filter can do its job. - The green filter around the laser works acceptably well and I'm relying on it most of the time for small jobs below 20% laser power BUT there are still many ways (underneath the shield and by the heatsink) where laser light WILL escape and kill your eye. So definitely wear proper protection glasses despite the mini-filter. Especially if you work with reflective materials or above 20% laser power. Cons: - No limit switches. - No power switch. - Fan is a bit too loud. WARRANTY-VOIDING hacks I did: - Flashed Arduino Optiboot. - Flashed GRBL 1.1h. - Added 12V power switch. - Added limit switches (for the homing to work you also need to recompile GRBL with the Z-axis homing disabled). - Wrapped the laser head with PET tape to force all of the fan's air down the heatsink.

    Comments (10)
  • 08/10/2020

    Megkaptam a gravírozót. Ismét sérült volt a csomagolás. Eddig a legjobban sérült csomagolásban kaptam meg, de a terméknek nem lett baja első ránézésre. Köszönhető a gondos védőcsomagolásnak! "Atombiztos" a csomagolása. Persze ez sem véd mindentől, de a képeken látható behatásoktól a tartalmat megvédte. Köszönöm. Remélem, hogy jól fog üzemelni... :-) Azt hiszem erről csinálok egy összeállítási videót. Úgysincs a nyelvünkön erről semmi... I got the engraver. The packaging was damaged again. I received it in the most damaged packaging so far, but the product is not damaged. Thanks to the careful protective packaging! The packaging is "atomically safe". Of course, this can’t protect against everything either, but it did protect the content from the damage seen in the pictures. Thanks. I hope it will work well ... :-) I think I’m making a compilation video of this. There is nothing about this in our language anyway ...

    Comments (1)
  • 24/01/2021

    It is quick and hassle-free.When installing the LaserGBRL driver, you need to get used to the order. First you need to install a driver and then connect the USB cable. For me, the laser with the focus set according to the factory description did not cut through the 240gr photo paper, only engraved. For this, I changed the value of the $110 line in the GBRL settings to about 500-600-650 mm/min after several attempts, so it is already cut.The photos show SMAX/ $110 values. The smallest $110 value where the paper is already cut out is recommended.Smoke extraction is recommended, as is retrofitting of the power chain for the control cables.The eye protection plexin visible dirt was created during the test. 752 / 5000 Translation results Where is already and hassle-free. You need to get ready to install the LaserGBRL driver. You must first install a driver and help us find the USB interface. This must be very difficult time the computer is still alive. In my life, the body with the body set to the ground description did not cut the 240gr each in the X-axis series, only engraved it. For this, I need the money in the $ 110 line in the GBRL series to about 500-600-650 mm / min, after all these changes, so it's all right. The reality show the SMAX / $ 110 million. The north side is the east side. The minimum price is $ 110 where you have very much cut out the window. Smokescreen is very clear, as is the retrofitting of a power source to the control systems as well.Visible results on the other side plexin was already using the test.

    Comments (2)
  • 07/03/2021

    product conforms to the description, very well packed, easy to mount, the software is to download from the Atomstack site, personally I use GRBL which is very easy to use, one groped initially to adjust the parameters (laser speed, power etc.) but after a few tests one arrives quickly to very good engraving results (see pictures below). ..) I would recommend if you want to do cutting to take a more powerful laser, this one 20W is too weak or then you have to do 20 passes to cut 3mm of balsa.. either take the 30 W or really better the 40 W but bcp more expensive... In short this engraver is really good for engraving and I really have fun with it, I recommend it...

    Comments (2)
  • 22/12/2020

    Good laser engraver, it works great. I succefully engraved: beer caps, wood, mirror, eeg^^... BUT delivery was not good, there was absolutly no update on the tracking untill it arrived at home (8weeks), then when i received it, the tracking was updated saying i will receive the parcel about 15 days later.... the aftersales service of bangood is good, they always answered me quickly.

    Comments (1)
  • 16/12/2020

    Arrived quickly after payment, perfectly packaged, quality is higher than expected, all-metal-frame, easy to assemble, works perfectly. On the end after minor modifications it is a pleasure to work with this laser-cnc. In the pictures is a poplar plywood 3mm, cutting 1500mm/min, 100% pwm , and 20 passes.... Excellent product. I highly recommend it.

    Comments (2)
  • 12/10/2020

    Quality is higher than expected. Build took about 1/2 hour, although might take longer if you new to these sort of builds. Was cutting paper in an hour. Used LaserGRBL to test and worked fine. Cut cardboard and 2mm felt no problem, yet to do anything more substantial. Was considering K40 instead of this, and had a little buyers remorse but after getting the unit I think it will do all I need without the additional hassle of CO2.

    Comments (2)
  • 04/02/2021

    After few days and with the upgrade with LCD touch ( for work without PC connected and with WiFi) I can engrave. With wood no problem buy with tiles i need mode attempt for best result 😅

    Comments (3)
  • 01/01/2021

    Very well thought-out kit, couldn't be easier to build. This is my first laser so it'll take some getting used to but there's plenty online tutorials to help out. Early days yet but so far so good. Going to be using it a lot in the next few days.

    Comments (2)
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$239.99
    • US$189.99
    • US$283.99
    • US$210.99
    • US$403.99
    • US$233.57
    • US$363.99
    • US$189.99
    • US$179.99
    • US$274.99
    • US$159.99
    • US$269.99
    • US$280.99
    • US$139.99
    • US$297.99
    • US$287.99
    • US$325.99
    • US$335.99