Motor

Mode: SE0702 KV28000 no plug version
Configu-ration:9N12P
Stator Diamter:7mm
Stator Length:2mm
Shaft Diameter:Φ1mm
Motor Dimension(Dia.*Len):Φ9.5mm*14mm
Weight(g):1.46g
No.of Cells(Lipo):1S only

Propellers

Materials: PC
Inch: 31mm
Pitch: 0.8 in
Weight: 0.21g
Mount hole diameter:  1mm

Flight controller

MCU: STM32G473CEU6
Gyro: ICM42688P
Sensor: Voltage & Current
BEC: 5V, Max. 2A
UART: UART 1, UART 2, UART 3 (For RX), UART 4(For VTX)
BetaFlight OSD: AT7456E
ESC: 5A continuous
RX: Serial ELRS 2.4GHz
RX antenna: Enameled copper wire 31mm length
Receiver firmware target: HappyModel EP1/EP2 2.4GHz RX
OPENVTX: 5.8GHz 48 channels, Max. 400mW
FC firmware target: CRAZYBEEG473
USB port: SH1.0-4Pin
Battery connector: A30
Mounting hole size: 25.5mm x 25.5mm
Weight: 3.83g without pigtail and vtx antenna

Onboard 4in1 ESC

Power supply: 1S LiPo/LiPo HV

Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay v0.21
Firmware target: A_X_5_96KHz
Default protocol: DSHOT300 DSHOT600
Recommend ESC Startup power value to min1100/max1200

Onboard Serial ExpressLRS receiver

Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V3.0
RF Frequency: 2.4GHz
Antenna : Enameled copper wire antenna
Telemetry output Power: <12dBm
Receiver protocol: Serial_based CRSF
Compatible with ExpressLRS V3.x.x TX Module
Could flash single ELRS receiver firmware by Wifi
ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx

Onboard 5.8g VTX

OPENVTX Firmware
Support firmware upgrade by openvtx configurator
Output power: PIT/10/25/100/400
Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz
Channel SEL: SmartAudio2.1
Modulation type: FM
Operating temperature: -10℃~+80℃
Antenna port: IPEX1/U.FL

Nano5 Camera

Image Sensor: 1/3″ CMOS
Horizontal Resolution: 1200 TVL
Lens: 2.1mm (M10) 155° FOV
TV System: NTSC
Signal-to-Noise Ratio: >52dB
Electronic Shutter: Auto
Automatic Gain Control (AGC): Auto
Minimum Illumination: 0.001Lux@1.2F
Digital Wide Dynamic Range: Auto
Power Supply: DC 3-5.5V
Current: 110mA@5V 120mA@3.3V
House Material: ABS
Net Weight: 1.57g (1.0mm plug version)

Mobula6 2024 V3

Mobula6 2024 V2

Flight controller

CrazybeeG473

SuperX ELRS V2.0

Firmware target

Betaflight 4.6 CrazybeeG473

Customized STM32F411

Built-in ExpressLRS receiver

Serial ELRS 2.4GHz

Serial ELRS 2.4GHz

Built-in Dshot ESC

5A

5A

Receiver antenna plug

Enameled Copper wire

Enameled Copper wire

Onboard VTX power

25mw~400mw

25mw~400mw

Brushless Motor

0702 KV28000 no plug

0702 KV28000 with plug

Propeller

Gemfan 1208-3 tri-blade

Gemfan 1208-3 tri-blade

Battery plug

A30(compatible with BT2.0)

A30(compatible with BT2.0)

Frame

Mobula6 2024 frame 2.76gram

Mobula6 2024 frame 2.76gram

Item Name

Qty

Mobula6 2024 1S 65mm whoop Drone Frame +Canopy

1

CrazybeeG473 AIO 5-IN-1 Flight controller

1

SE0702 KV28000 brushless motor

4

Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw)

1

HQPROP ultralight whoop prop 1.2×1.1×3(2cw+2ccw)

1

Nano5 1200TVL camera NTSC 4:3

1

Onboard 5.8G 25mw~400mw VTX

1

Spare canopy

1

Propeller disassemble tool

1

Screw driver

1